RocketFish RF-WHD200 - Manual

Setting up the WirelessHD Kit
Tips:
• Test the placement of the transmitter and receiver for a good signal prior to permanently mounting or
installing everything.
• For best performance and range, mount the receiver vertically on the wall next to the TV (not behind
the TV), or upside-down on the ceiling next to the projector. Make sure that you can see the
Rocketfish and WiHD logos on the receiver from the location in the room where the transmitter is
located. For more details about mounting the receiver, see your User Guide.
• Use only good quality high-speed HDMI cables for all connections, such as Rocketfish brand cables.
Poorly constructed HDMI cables can negatively impact performance and may not support all of the
features included in your connected devices.
• Do not place the transmitter or receiver inside a cabinet or other location where they will not have a
clear view of the room.
RF-WHD200 I 4-port Wireless HD Kit
Quick Setup Guide
Introduction
Thank you for purchasing the Rocketfish 4-port WirelessHD Kit. Please follow the steps in this Quick Setup
Guide to ensure a successful installation of this product. If you experience any difficulty setting the product
up after referring to this guide, please consult the more detailed User Guide, also included in the package,
which contains some troubleshooting techniques that may help. If the additional instructions and
troubleshooting section of the User Guide prove unsuccessful for your setup, please contact our customer
service department at 800-620-2790 or visit www.rocketfishproducts.com for additional assistance.
This product is designed to wirelessly send fully uncompressed signals from up to four HDMI source
devices, such as a Blu-ray player, cable/satellite set-top box, gaming console, laptop, etc., to a HDTV or
projector at a distance of up to 30 feet within the same room. It is important to note that the 60 GHz
frequency with which this product transmits provides the necessary bandwidth to send every bit of
information from the source device to the display with no compression or bit dropping, but does not
penetrate wall or floors. Therefore, this product is not designed to send signals from one room to another.
Package contents
• 60 GHz WirelessHD transmitter
• 60 GHz WirelessHD receiver
• High-speed HDMI cables (2)
• Wall mounting bracket
(for use with the receiver)
1 Connect your HDMI source devices (up to four) to the WirelessHD transmitter with high-speed
HDMI cables.
2 Connect the WirelessHD receiver to the TV or projector with a high-speed HDMI cable.
3 Connect the included AC adapters for the transmitter and receiver to the DC input jacks, then plug
them both into an available AC outlet.
Note: The included AC adapters are labeled to ensure the correct adapter is used with the
transmitter and receiver.
4 Power on the TV or projector and at least one of the source devices that is connected to the
transmitter.
Note: Be sure the TV or projector is switched to the HDMI input to which the WirelessHD receiver is
connected.
5 Switch the Power switches on the transmitter and receiver to the ON position (it does not matter
which one you power on first). The HDMI input port LED on the transmitter should light
continuously (stop blinking) to indicate that the desired input is selected. If this doesn't happen
automatically, use the included remote control or HDMI Select Switch on the back of the
transmitter to select the desired input port. For more details on HDMI port switching, see your User
Guide.
Note: The Power and Link Status indicator LED will flash while the transmitter and receiver establish
a connection. Once the connection has been established, these indicators will light continuously
(stop flashing).
For more detailed instructions on operating the WirelessHD kit, please refer to the included User Guide
section, “Operating the WirelessHD kit”.
Top view Side view
Transmitter
Receiver
32.8 ft.
(10 m)
82° 82°
16.4 ft.
(5 m)
16.4 ft.
(5 m)
Transmitter Receiver
32.8 ft.
(10 m)
47°
47°
16.4 ft. (5 m)
16.4 ft. (5 m)
Floor
OR
HDMI cable
Blu-ray/DVD
HDMI cable(s)
• Remote control
• AC power adapters
(2 - one for the transmitter, one for the receiver)
• Quick Setup Guide
• User Guide
RF-WHD200_10-1354_QSG_V5_EN.eps 1 3/14/2011 3:01:32 PM RF-WHD200_10-1354_QSG_V5_EN.eps 1 3/14/2011 3:01:32 PM