Roland E-09 - Manual (Page 23)

23
Function Menu
BALANCE [ ] (ARRANGER) adjusts the volume of all arranger parts.
FSW Sustain,
Sostenuto,
Soft,
Rotary S/F,
Start/Stop,
BassInv,
PunchI/O
(default: Sus-
tain) Assigns the function performed by a separately available foot switch connected to the rear panel FOOT
SWITCH jack.
Sustain: The foot switch will function as a sustain pedal (also called “hold” or “damper”). While you
hold down the pedal, notes will be sustained even after you take your fingers off the keyboard.
Sostenuto: The foot switch will function as a Sostenuto pedal, sustaining only the notes that had already
been pressed at the moment you pressed the pedal. (Subsequently played notes will not be sus-
tained.) This function is available only for the keyboard parts.
Soft: The foot switch will function as a Soft pedal. Notes played while holding down the pedal will
sound softer. This function is available only for the keyboard parts.
Rotary S/F: The foot switch will switch the speed of the rotary effect. This is valid only if the “Rotary” type
is set to MFX. (p. 18)
Start/Stop: The foot switch will start/stop playback for the arranger or song. This is the same function as
[START/STOP].
BassInv: The foot switch will turn the Bass Inversion function on/off. (p. 24)
PunchI/O: The foot switch will control punch-in and punch-out when you are using punch-in/out record-
ing. (p. 21)
METRONOME Parameters
Parameter Value Explanation
Metro TS 1/4–6/4,
6/8, 9/8
(default: 4/4) Specifies the time signature of the metronome (the number of beats per measure). This setting will change au-
tomatically when you select a music style that has a different time signature. For details on using the metro-
nome, refer to p. 11.
This screen will also appear if you hold down [METRONOME] for a few moments.
Metro Vol 0–127
(default: 100) Specifies the volume of the metronome.
Octave Parameters
Parameter Value Explanation
Main Oct * -4–0–4
(default: 0) Raises or lowers the octave setting of the Main part in steps of one octave.
* If a drum set is assigned to the Main part, this parameter does not transpose the pitch of the drum/percussion
sounds, but instead changes the drum/percussion sounds that are assigned to the keys.
Dual Oct * -4–0–4
(default: 0) Raises or lowers the octave setting of the Dual part in steps of one octave.
Split Oct * -4–0–4
(default: 0) Raises or lowers the octave setting of the Split part in steps of one octave.
Volume Parameters
Parameter Value Explanation
Main Vol * 0–127
(default: 127) Adjusts the volume of the Main part.
You can also adjust this by holding down [TONE] and using BALANCE [ ][ ]. (p. 10)
Dual Vol * 0–127
(default: 110) Adjusts the volume of the Dual part.
You can also adjust this by holding down [DUAL] and using BALANCE [ ][ ]. (p. 10)
Split Vol * 0–127
(default: 75) Adjusts the volume of the Split part.
You can also adjust this by holding down [SPLIT] and using BALANCE [ ][ ]. (p. 10)
Auto Bass OFF, 0–127
(default: OFF) When the Split part is on, this adjusts the volume of the Auto Bass part (which plays a monophonic bass ac-
cording to the chord you play). Turn this OFF if you don’t need the Auto Bass part.
If the Bass Inversion function (p. 24) is off, the root of the chord you play with your left hand (using the Split
part) is sounded by the Auto Bass part.
The Auto Bass part follows the Educational setting (p. 24).
Acc Drum * 0–127
(default: 100) Adjusts the volume of the arranger’s drum part.
Acc Bass * 0–127
(default: 100) Adjusts the volume of the arranger’s bass part.
Accomp * 0–127
(default: 100) Adjusts the volume of the arranger’s Accomp parts 1–6.
Parameter Value Explanation
E-09_e.book 23 ページ ２００５年１１月２１日 月曜日 午前１１時２４分