Onkyo DR-L50 - Manual (Page 27)

27 27
■ Setting the TV System
The default setting of the DVD Receiver is AUTO, and unless you
notice that the picture is distorted when playing some discs, you
should leave it set to AUTO.
If you experience picture distortion with some discs, set the TV
system to match your country or region’s system. Doing this,
however, may restrict the kinds of disc you can watch. The table
below shows what kinds of disc are compatible with each setting
(AUTO, PAL and NTSC).
1 Switch the DVD Receiver into standby.
2 Hold down
¢ then press STANDBY/ON until the display
indicates the new setting to switch the TV system.
The TV system changes as follows:
AUTO
= NTSC
NTSC = PAL
PAL = AUTO
Note that you have to switch the DVD receiver into standby
before each change.
About MOD. (Modulation) PAL
• SHRINK
Most models of the newly developed countdown PAL TV system
detect 50 Hz (PAL)/60 Hz (NTSC) and automatically switch
vertical amplitude, resulting in a display without vertical
shrinkage.
• If your PAL TV does not have a V-Hold control, you may not be
able to view NTSC disc because the picture may roll. If the TV
has a V-Hold control, adjust it until the picture stops rolling. On
some TVs, the picture may shrink vertically, leaving black bands
at the top and bottom of the screen. This is not a malfunction; it is
caused by the NTSC
= PAL conversion.
Type
DVD
Video CD
CD, No disc
Format
NTSC
PAL
NTSC
PAL
Disc Output format
Position of TV SYSTEM mode
NTSC PAL AUTO
NTSC MOD. PAL NTSC
PAL PAL
NTSC MOD. PAL NTSC
NTSC PAL PAL
NTSC PAL NTSC or PAL
■ Turning the unit on/off with the TV’s power
switch — IPM function
The DVD Receiver is equipped with the (IPM) system.
Just turn on your TV’s power switch and, in about 5 seconds,
the DVD Receiver turns on automatically. If you turn off the
TV’s power switch, IPM indicator flashes on the display and
the DVD Receiver automatically turns off in about 5 minutes.
To activate the IPM function
1 Connect the audio output of your TV’s audio output to the
DVD Receiver’s TV/LINE IN L/R jacks (refer to pages 18
and 19).
Even when connected with SCART cable, audio
connection to TV/LINE IN L/R jacks is needed (European
model).
2 Press IPM on the remote controller repeatedly to turn on
the IPM indicator on the unit.
Notes
• The IPM system may not function properly with some TV sets.
• When using monaural TV, connect the audio output of the TV to
the DVD Receiver’s TV/LINE IN L jack.
• When the TV is turned off while the DVD Receiver selects other
input source, the DVD Receiver does not turn off.
IPM
LATE NIGHT
7
TV/ SETUP TV/ SETUP
TEST TONE SP SETUP CH SEL
DISTANCE SW MODE UP
TV MUTING
TV POWER TV INPUT
T-D SETUP IPM DOWN
TV VOL +
TV VOL -
9
TV CH - TV CH +
VOLUME
ON
STANDBY INPUT SELECTOR
RECEIVER
COND.M LAST M FUNC.M
ANGLE AUDIO SUBTITLE
T-D/ ST LATE NIGHT
TOP MENU MENU
RETURN DVD
SETUP
REPEAT
TUNING TUNER PRESET
MD / CDR / TAPE
A-B STEP/ SLOW
TIMER
CLEAR
PROGRAM
SEARCH
ACOUSTIC
CONTROL
SURROUND
RANDOM
--/---
MODE
SLEEP
MUTING
DIMMER DISPLAY CLOCK
MODE
+10 0 SHIFT
9
4 5 6
7 8
1 2 3
IPM Before operating the
remote controller
Press MODE TV/SETUP.
Theater-Dimensional
IPM