Onkyo TX-SR309 - Manual (Page 32)

32
En
Menu Level Cal
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
■ Left, Center *1 , Right, Surround Right, Surround
Left
` –12 dB to 0 dB to +12 dB in 1 dB step.
■ Subwoofer *1
`
–15 dB to 0 dB to +12 dB in 1 dB step.
Note
• Speakers that you set to “No” or “None” in the “Sp Config
(Speaker Configuration)” (
➔ page 31) cannot be selected.
• These settings cannot be calibrated in either of the following
cases:
– a pair of headphones is connected.
– Speakers B is on.
– Speakers A is off.
– the “Audio TV Out” setting is set to “On” (
➔ page 35).
– “HDMI Ctrl (RIHD)” is set to “On” (
➔
page 35) and
you’re listening through your TV speakers.
– the AV receiver is muted.
*1 For the center speaker and subwoofer, the level settings made
by using HOME are saved here as the default settings.
Tip
• If you’re using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
Menu Audio Adjust
With the Audio Adjust functions and settings, you can
adjust the sound and listening modes as you like.
Multiplex/Mono Settings
■
Multiplex
Input Ch (Mux)
`
Main
` Sub
`
Main/Sub
This setting determines which channel of a stereo
multiplex source is output. Use it to select audio channels
or languages with multiplex sources, multilingual TV
broadcasts, and so on.
■
Mono
Input Ch (Mono)
` Left + Right
`
Left
`
Right
This setting specifies the channel to be used for playing
any 2-channel digital source such as Dolby Digital, or 2-
channel analog/PCM source in the Mono listening mode.
Dolby Settings
■
PLII Music (2ch Input)
These settings apply to only 2-channel stereo sources.
Panorama
`
On
`
Off
Turn this setting on to broaden the width of the front
stereo image when using the Dolby Pro Logic II Music
listening mode.
Dimension
`
–3 to 0 to +3
With this setting, you can move the sound field forward or
backward when using the Dolby Pro Logic II Music
listening mode. Higher settings move the sound field
backward. Lower settings move it forward.
If the stereo image feels too wide, or there’s too much
surround sound, move the sound field forward to improve
the balance. Conversely, if the stereo image feels like it’s
in mono, or there’s not enough surround sound, move it
backward.
Center Width
`
0 to 3 to 7
With this setting, you can adjust the width of the sound
from the center speaker when using the Dolby Pro Logic
II Music listening mode. Normally, if you’re using a
center speaker, the center channel sound is output from
only the center speaker. (If you’re not using a center
speaker, the center channel sound will be distributed to the
front left and right speakers to create a phantom center).
This setting controls the front left, right, and center mix,
allowing you to adjust the weight of the center channel
sound.
DTS Setting
■
Neo:6 Music
Center Image
`
0 to 2 to 5
With this setting, you can specify by how much the front
left and right channel output is attenuated in order to
create the center channel.
Setting a value “0” in the middle is set to hear a sound.
Sound is spread in left and right (the outside) so that the
set value is made big. Please adjust by liking.
Level Cal (Level Calibration)
Audio Adjust