Sylvania 6620LF4 - Manual (Page 2)

INSTALLING THE BATTERIES
Install two AAA batteries (supplied)
matching the polarity indicated inside
battery compartment of the remote con-
trol.
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
PREPARATION FOR USE
[ANTENNA CONNECTION] [CATV/SATELLITE CONNECTION]
2 1 3
CONNECTIONS
VIDEO2
R
L
Y
Pb
Pr
AUDIO
COMPONENT
R
L
VIDEO
S-VIDEO
ANT
AUDIO
VIDEO1
HEAD PHONE
L
Y
Pb
Pr
R
L
VIDEO2
AUDIO R
VIDE O1
S-VID EO
VIDEO
HEA D PH ONE
ANT
A U D I O
COMPONENT
OPERATIONS
VIDEO2 input
VIDEO2
R
L
Y
Pb
Pr
AUDIO
COMPONENT
R
L
VIDEO
S-VIDEO
ANT
AUDIO
VIDEO1
HEAD PHONE
L
Y
Pb
Pr
R
L
VIDEO2
AUDIO R
VIDEO 1
S-VID EO
VIDEO
HEA D PH ONE
ANT
A U D I O
COMPONENT
Note:
● If some digits appear in the corner of the screen when the unit is turned on for the first time, hit
[POWER] without unplugging the power cord.
Audio Cable
Video Cassette
Recorder
Notes:
● The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for
connecting monaural audio equipment.
● The S-VIDEO jack is given priority over the VIDEO jack.
Component
Video Cable
Audio Cable
Video Game
Video Camera
Rear of this TV
Rear of this TV
Note:
● The TV can only accept a 480i (interlaced) video signal.
REMOTE CONTROL AND FRONT PANEL FUNCTION
1 2 3
4 5 6
7 8 9
0 +100 MENU
o
n
p m
MUTE SLEEP
DISPLAY
CH RET
INPUT
SELECT
POWER
CH
VOL
POWER button
To turn TV on/off
Channel number buttons
CH(ANNEL) K K / L L buttons
MENU button
To view on-screen menu SLEEP button
To set Sleep Timer
DISPLAY button
To display CH No./Audio Status
CH(ANNEL) RET(URN) button
To return to previous channel
INPUT SELECT button
To select TV or external input
MUTE button
To mute sound
VOL(UME) X X / Y Y buttons
To adjust volume
To select channels
POWER
MENU VOLUME CHANNEL INPUT SELECT POWER
MENU VOLUME CHANNEL INPUT SELECT POWER
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
[EXTERNAL CONNECTION]
ex.
ex.
Cables used here are available on the market.
* Some cable TV systems use scrambled signals and
require a special converter to receive these channels.
Consult your local cable company.
OUT IN
L
Y
Pb
Pr
R
L
VIDEO2
AUDIO R
VIDE O1
S-VID EO
VIDEO
HEA D PH ONE
ANT
A U D I O
COMPONENT
ANT
UHF
VHF
VHF/UHF
VHF/UHF
Combiner
OR
OR
75-ohm
Coaxial Cable
From Cable
System
From Cable
System
or Satellite
Antenna
CATV Box *
or Satellite Box
(OUT)
(OUT)
(IN)
(IN)
(OUT)
(OUT)
(IN)
(IN)
Note:
• For your safety and to avoid damages to the unit, unplug the antenna cable from the
ANT jack before moving the unit.
(OUT)
Video Cable
S-Video Cable
(IN)
SELECTING AUDIO/VIDEO INPUT
When you use the AUDIO/VIDEO input jacks, select “VIDEO1” or “VIDEO2” mode by hit-
ting
[INPUT SELECT] on the remote control. The input mode changes by hitting the button
as following:
TV channel VIDEO1 VIDEO2 INPUT
SELECT
VIDEO1 input
You can bracket this product as wall mounting TV using the arm adapted for 100mm (commer-
cially available).
RF Cable
RF Cable
OR
POWER button
To turn TV on/off
VOLUME K K / L L buttons
To adjust volume
INPUT SELECT button
CHANNEL K K / L L buttons
To select channels
MENU button
To view on-screen menu
Infrared Sensor Window
Power Indicator
Flat twin-lead
cable
Tilt Stand
Adjust the stand to change the angle of TV (-5 ° – 10°).
5 ° 10°
TILT STAND