Omega Vehicle Security 850i - Manual (Page 15)

the Vehicle Recovery operation from the transmitter or transceiver in the event
that you are forced from your car. “Remote Activated” Vehicle Recovery is one
three methods of activating this feature, which is explained on page 27.
Programming Transmitter Activated Anti Car-Jacking:
Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and
released sixteen times. The system’s response will be sixteen siren chirps, and
the Status Light flashing sixteen times, pausing, then repeating. Within 10
seconds, press and release the transmitter/transceiver’s "Arm/Lock" button to
turn on the Transmitter Activated Vehicle Recovery feature (the siren chirps
once) or the "Disarm/Unlock" button to turn the feature off (the siren chirps twice).
Feature #17 Chirp Confirmation
(Factory Default Setting On)
This feature allows the permanent removal of the system’s chirping the siren
as an audible confirmation when performing functions such as Arming and
Disarming. Please note that utilizing this feature to remove the confirmation
chirps does not affect siren chirping operations associated with the Unauthorized
Transmitter Alert warning, sensor prewarning or Programming Mode.
Note: Using this feature to turn off the siren chirps also turns the chirps in the
Echo transceiver- the Echo emulates the system’s siren chirps.
Programming the Chirp Confirmation:
Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and
released seventeen times. The system’s response will be seventeen siren chirps,
and the Status Light flashing seventeen times, pausing, then repeating. Within
10 seconds, press and release the transmitter/transceiver’s "Arm/Lock" button to
turn the Chirp Confirmation on (the siren will chirp once) or the "Disarm/
Unlock" button to turn the Chirp Confirmation off (the siren will chirp twice).
Feature #18 Remote Start Run Time 10 Or 20 Minutes
(Factory Default Setting 10 Minutes)
This Feature sets the period of time that the engine will run after being
remotely started. If the engine is not stopped by a transmitter or transceiver, or
a safety circuit violation, the engine will automatically stop upon the expiration
of the selected time period.
Programming 10 or 20 Minute Run Time:
Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and
released eighteen times. The system’s response will be eighteen siren chirps, and
the Status Light flashing eighteen times, pausing, then repeating. Within 10
seconds, press and release the transmitter/transceiver’s "Arm/Lock" button to
Page 36
Emergency Override:
In the event that your transmitter is lost, damaged, or its batteries have become
exhausted, the Valet Switch and the vehicle’s ignition key may be used to disarm
the system. These Emergency Override instructions reflect a default setting of “1
press”; the “SecureCode” programmable feature allows the user to customize the
number of Valet Switch presses needed for the Emergency Override. The
SecureCode Emergency Override is described on the following page.
DISARMING BY EMERGENCY OVERRIDE
Page 13
To Disarm the System without using a Transmitter:
matic Rearming period. For example, if a vehicle door is opened during the
90 second period, the countdown will stop. When the door is closed, the
system resets and starts a new 90 second countdown period.
• The Automatic Rearming sequence is indicated by a fast flashing Red Status
Indicator Light, unless the system has been activated, in which case a Zone
Violation Code will flash instead (pages 25-26). The ignition switch must
be turned on to erase a violation code.
• If the system is disarmed while it is activated (siren sounding and lights
flashing) Safety Disarm will cancel the Automatic Rearming for that disarming
operation only. The next time the system is armed, Automatic Rearming will
be initiated upon the subsequent disarming.
ENTER THE VEHICLE
AND USE YOUR KEY TO
TURN THE IGNITION ON
THE SYSTEM WILL DISARM
WITHIN 5 SECONDS
OF TURNING THE
IGNITION ON, PRESS
AND RELEASE THE
VALET SWITCH
( ( (
ECHO
Step 1 With the system in the armed condition, enter the vehicle via the driver's
door (be aware that the system will activate to an alarm condition when
the door is opened).
Step 2 Using the ignition key, turn the vehicle’s ignition on.
Step 3 Within 5 seconds, press and release the Valet Switch once. The system
will immediately disarm.
A procedure which separate, but similar, to an Emergency Override is the Alarm