Onkyo AV Receiver TX-NR509 User Manual
Page 29
29
En
Note
• You can cancel Audyssey 2EQ Room Correction and Speaker
Setup at any point in this procedure simply by disconnecting the
setup microphone.
• Do not connect or disconnect any speakers during
Audyssey 2EQ Room Correction and Speaker Setup.
• If the AV receiver is muted, it will be unmuted automatically
when Audyssey 2EQ Room Correction and Speaker Setup
starts.
• Changes to the room after Audyssey 2EQ Room Correction and
Speaker Setup require you run Audyssey 2EQ Room Correction
and Speaker Setup again, as room EQ characteristics may have
changed.
Error Messages
While Audyssey 2EQ
®
Room Correction and Speaker
Setup is in progress, one of the error messages below may
appear.
The options are:
`
Retry:
Try again.
`
Cancel:
Cancel Audyssey 2EQ Room Correction and
Speaker Setup.
• Ambient noise is too high.
The background noise is too loud. Remove the source of
the noise and try again.
• Speaker matching error!
The number of speakers detected was different from
that of the first measurement. Check the speaker
connection.
• Writing Error!
This message appears if saving fails. Try saving again.
If this message appears after 2 or 3 attempts, contact
your Onkyo dealer.
• Speaker Detect Error
This message appears if a speaker is not detected. “No”
means that no speaker was detected.
Tip
• See “Speaker Configuration” for appropriate settings
page 12).
Changing the Speaker Setup Manually
You can manually make changes to the settings found
during Audyssey 2EQ Room Correction and Speaker
Setup.
See also:
• “Sp Config (Speaker Configuration)” (
• “Sp Distance (Speaker Distance)” (
• “Level Cal (Level Calibration)” (
4
Press
ENTER.
Audyssey 2EQ
®
Room Correction and Speaker Setup
starts.
Test tones are played through each speaker as
Audyssey 2EQ Room Correction and Speaker Setup
runs. This process takes a few minutes. Please
refrain from talking during measurements and do
not stand between speakers and the microphone.
Do not disconnect the speaker setup microphone
during Audyssey 2EQ Room Correction and Speaker
Setup, unless you want to cancel the setup.
If you select “Audyssey Quick Start”, you will go to
step 7.
5
Place the setup microphone at the next position,
and then press
ENTER.
Audyssey 2EQ performs more measurements. This
takes a few minutes.
6
When prompted, place the setup microphone at
the next position, and repeat step 5.
7
Use / to select an option, and then press
ENTER.
The options are:
`
Save:
Save the calculated settings and exit
Audyssey 2EQ Room Correction and Speaker
Setup.
`
Cancel:
Cancel Audyssey 2EQ Room Correction and
Speaker Setup.
Note
• You can view the calculated settings for the speaker
configuration, speaker distances, and speaker levels by
using
/
.
8
Use / to select a target, and use
/
to change
the setting.
After the results of Audyssey 2EQ have been saved,
the menu will display the “Audyssey” (
page 44),
(
page 45) settings.
Note
• When “Audyssey Quick Start” has been used for
measurement, “Audyssey” cannot be selected.
• These settings are applied to all input selectors.
9
Press
ENTER.
10
Disconnect the speaker setup microphone.
Subwoofer :
Yes
Front :
Small
Center :
Small
Surround :
Small
Surr Back
:
Small
Surr Back Ch
:
2ch
Crossover :
100Hz
Save
Cancel
2EQ: Auto Setup
Audyssey
<- Review Speaker Configuration ->
Retry
Cancel
Ambient noise is too high.
2EQ: Auto Setup
Audyssey
Error message