Oregon WRS368 User Manual

Page 10

Advertising

NOTE

If you increase (or decrease) the volume while

the speaker is on mute, the Mute function will deactivate
and the volume will turn on again.

ADJUSTING BASS AND TREBLE

Adjusting the Wireless Remote Speaker's bass and
treble settings allows the device to playback audio with
a different range of sound and tonal effects.

To adjust the bass sound:

1. Press the button once.

appears on the LCD.

2. Use the

buttons to increase or decrease the

bass. To continuously increase or decrease the bass,
press and hold the

button down until the

desired bass level is reached.

3. Press the button again.

appears on the LCD.

To adjust the treble sound:

1. Use the

buttons to increase or decrease the

treble. To continuously increase or decrease the
treble, press and hold the

button down until

the desired treble level is reached.

2. Press the button once to exit.

"Auto quit" activates when idle for more than

10 seconds.

CHANGING AUDIO SOURCES

If all audio source cables are properly connected to the
Transmitter, you may change to and from any source
with a convenient press of the

button. The LCD

backlight changes colour to indicate the change in audio
source.

1. To change the audio source, press the

button.

The default setting is source

2. Press the

button again to change the audio

source to source

. The audio source icon will

change from Source

to Source .

3. Press the

button a third time to select the third

audio source.

4. To change the audio source at any time, repeatedly

press the

button until the desired source is

shown on the LCD.

SETTING THE CLOCK

To set the time:

1. Press the

button. Both hands on the clock will

begin flashing.

2. Use the

buttons to set the time: press the

button once to advance the clock by 1 minute and
press the

button to turn the clock back by

1 minute. Press and hold the

buttons down

to set the time faster.

3. Press the

button to confirm the newly set time

and exit the clock setting mode.

The clock can only be adjusted by minute

increments and not by hour increments.

No other buttons can be pressed while the

setting clock function is on. "Auto quit" activates when
the function is idle for more than 30 seconds; the last
time that was set prior to idling is not saved.

Regardless of whether your Wireless Remote

Speaker is powered on or off, the clock will still show on
the LCD.

THE REMOTE LEARNING FUNCTION

Oregon Scientific does not assure the

compatibility of this product with all Audio / Video devices
existing in the market.

The Remote Learning function allows you to use a
remote control device of an audio source(s) connected
to the Transmitter to adjust the Wireless Remote
Speaker's volume and activate the mute function,
regardless of where the audio source is located.
Essentially, the remote control device of the audio
source, for example, a DVD player, becomes the
speaker's remote control device.

Make sure you are using fresh batteries in both

the audio source's remote control and in the Wireless
Remote Speaker, if used.

Incandescent or low-energy light can cause

interference with the infrared transmissions. When using
the Learning function, keep the audio source's remote
control and Wireless Remote Speaker at least
0.9 m (3 feet) away from such light sources.

"Auto quit" activates when idle for more than

60 seconds.

LEARNING TO INCREASE VOLUME USING THE
AUDIO SOURCE REMOTE CONTROL DEVICE

To teach your remote control device to increase volume:

1. Check that your desired audio source is

displayed on the LCD. You may choose from any of
the 3 sources.

2. Point the top of your audio source's remote control

device at the base of the Wireless Remote Speaker
so the infrared sensor on the remote control is in
line with the infrared sensor located at the bottom of
the speaker.

NOTE

AUDIO SOURCE

LCD COLOUR

Red

Green

Source

Blue

NOTE

WRS368 Eng (US) R18 OP

7/30/05, 10:51 AM

Advertising

Popular Brands

Popular manuals