Tiger WonderBorg 70709 - Manual (Page 9)

16 15
5-1
Insert three AAA alkaline batteries (sold
separately) in the WonderBorg, as shown
in the diagram. Be careful to insert the
batteries the right way.
5-2
Place the battery cover on top of the
battery box. Be careful to position the
battery cover with the holes positioned
as shown in the diagram.
5-3
Turn the WonderBorg’s POWER switch ON.
The WonderBorg’s legs will move slightly,
then stop immediately. The WonderBorg
will make a beeping noise, and the green
LED will light up.
5-4
Turn the POWER switch ON.
5-5
Place your WonderBorg on the leg and Antenna
Bending Template on the page 56 of this
manual. Bend the legs and antennae to match
the illustration. They can be adjusted to
any position. Once you have finished the
adjustments, turn the power OFF.
If the WonderBorg does not work, check
whether you have made a mistake in the
assembly operation.
Points to check:
-
Are the connectors plugged in correctly?
- Are the batteries inserted the
right way?
The bending of the legs and antennae is
now complete.
Note: When the power is ON, the legs may
move, so turn the power ON before adjusting
them.
Extra Information
By changing the angle of the motor units,
you can adjust the height of the WonderBorg.
Note: If you adjust the angle of the motor
units closer to the vertical direction
(making the body higher), the WonderBorg
will walk more smoothly over obstacles,
but it will also be more prone to falling
over.
Likewise, if you adjust the angle of the
motor units closer to the horizontal
direction (making the body lower), the
WonderBorg will be less prone to falling
over, but it will also be less inclined
to walk over obstacles. The angle is altered
in four stages.
Green LED Power Switch
[ON]
[OFF]
Bending the Legs and Antennae
6-1
Press the body shell down on to the
WonderBorg s body so that the pins on the
left and right side of the frame slot
into the holes in the body shell. The
START / STOP switch should protrude through
the hole.
6-2
Adjust the angle of the left and right
motor units one stage away from the
horizontal, so that they are slanted like
the sides of the letter "A".
The WonderBorg is now complete. Next, carry
out the following operational tests.
7-1
Place the WonderBorg on the floor and turn
the POWER switch ON. The legs should move
slightly, then stop immediately. The
WonderBorg should emit a beeping noise,
and the green LED should light up.
7-2
7-3
The WonderBorg should emit a modulated
beeping noise and start walking.
7-4
The WonderBorg is pre-programmed with a
test program (which is erased when you send
it new data). Please check the following
functions.
-
Press right antenna: Rotates to the right
- Press left antenna: Rotates to the left
- Obstacle to right: Right eye LED flashes
- Obstacle to left: Left eye LED flashes
If the WonderBorg does not work correctly,
check whether you have made a mistake in
the assembly operation.
Point to check:
- Are the connectors plugged in correctly?
- Are the batteries inserted the right way?
7-5
To halt the WonderBorg, press the START /
STOP switch again.
7-6
Turn the POWER switch OFF. The
operational testing is now over.
Align the holes with the Pins
Pins Push Down
Adjust the angle of both
motor units by one Stage
Holes
The START / STOP Switch should
Stick out through the hole
[ON]
Press START / STOP
Switch
Power Switch
[Off]
Fitting the Body Shell Operational Testing
AAA/LR03 1.5V
AAA/LR03 1.5V
AAA/LR03 1.5V
AAA/LR03 1.5V
AAA/LR03 1.5V
AAA/LR03 1.5V
HARDWARE BASICS HARDWARE BASICS