Tamron Digital Compact Hi-Fi System CE510S - Manual (Page 3)

5
PREPARATIONS AND CONTROLS
PREPARATIONS
1. Carefully unpack the unit and speakers. Remove all packing material from around the unit.
2. Locate the unit horizontally on a heavy duty stand or firm level surface and away from the
speaker system to avoid acoustic feedback.
CONNECTIONS
1. Connect the Speaker wires from Speaker Box to the Speaker Outlet on the rear of the main
unit.
2. Connect the AC power cord to the AC outlet.
3. Press the POWER button [8] to turn on the unit.
NOTE:
- Before operating the unit in a new area for the first time, it is absolutely necessary to check the
operating voltage of your unit is identical with the voltage of your local power supply.
- This unit is to be operated only at the printed power source voltage on the back panel.
- When the unit will not being used for a long period, you must disconnect the AC power cord
from AC outlet.
SOUND CONTROL
VOLUME:
Press the VOLUME UP button [20] to increase the volume, and the VOLUME DOWN button [20]
to decrease the volume.
CLOCK ADJUSTMENT
1. Set the FUNCTION switch [9] to “TAPE” mode. The clock will appear on the LCD display
[11].
2. Press the MEMORY/ CLOCK ADJ. button [5] once to adjust the hour. Press the button once
more to adjust the minute.
3. Press the F.SKIP/ TUNING UP/ ADJ. UP button [2] and the B. SKIP/ TUNING DOWN/ ADJ.
DOWN button [3] to set the time.
- Press the F. SKIP/ TUNING UP/ ADJ. UP button once to add one hour or one minute to the
time setting. When keep pressing the button, the “hour” or “minute” setting is increased
continuously until the button is released.
- Press the B. SKIP/ TUNING DOWN/ ADJ. DOWN button once to reduce one hour or one
minute to the time setting. When keep pressing the button, the “hour” or “minute” setting
is decreased continuously until the button is released.
4. Press the MEMORY/ CLOCK ADJ. button again to confirm the time setting.
5. If the unit is in the “RADIO” or “CD” mode, press the MODE/ REMAIN button [7] and repeat
step 2-4.
RADIO OPERATION
1. Press the POWER button [8] once to turn the unit on.
2. Set the FUNCTION switch [9] to “RADIO” mode.
3. Set the BAND selector [10] to the desired band.
4. Press the F. SKIP/ TUNING UP/ ADJ. UP button [2] or B. SKIP/ TUNING DOWN/ ADJ.
DWON button [3] momentarily (less than 0.5 sec.) to step up or down the receiving frequency
in order to select the desired station.
5. For auto tuning, keep pressing the F. SKIP/ TUNING UP/ ADJ. UP button or B. SKIP/ TUNING
DOWN/ ADJ. DWON button (more than 0.5 sec.) until the displayed frequency starts to
change, then release the button. Tuning will stop automatically when a station is received.
6. To turn the unit off after use, simply press the POWER button once again.
FM RECEPTION
Raise and extend the FM antenna wire [23], then adjust the position for the best reception. ST
indicator will appear on the display only if an actual stereo broadcast station is being received.
AM RECEPTION
Rotate horizontally or relocate the unit for best reception as the built-in ferrite bar antenna is
directional.
PRESET STATIONS
1. Set the FUNCTION switch [9] to “RADIO” mode.
2. Set the BAND selector [10] to the desired band.
3. When a desired station is tuned, press the MEMORY/ CLOCK ADJ. button [5] and then
select the desired station you want to store by pressing the REPEAT/ MEM. UP button [6].
4. Press the MEMORY/ CLOCK ADJ. button again to confirm the preset station.
5. Repeat steps 3 and 4 to enter remaining preset stations.
NOTE: The preset memory operating can be repeated to store a maximum of 10 FM stations and
10 AM stations.
RECEIVING A PRESET STATION
To recall any preset station within the selected band, simply press REPEAT/ MEM. UP button [6]
until preset number selection appears on the display.