Tunturi E4R User Manual
Page 4
4
OWNER’S MANUAL
•
E4R
GB
O W N E R ’ S M A N U A L
•
E 4 R
5
ASSEMBLY
Open the transport package on its side. Take
the parts out of the package and make sure the
package includes all the following parts:
1.
Front frame
2.
Lower frame
3.
Seat frame
4.
Seat (2 pcs)
5.
Handlebar
6.
Meter
7.
Feet (2 pcs)
8.
Pedals (2 pcs)
9.
Water bottle holder
10.
Assembly kit (contents marked with in the
spare part list): keep the assembly tools, as you
may need them e.g. for adjusting the equipment.
You’ll find a spare part list at the back of this
guide. If necessary, please contact your dealer
with the model, equipment serial no. and spare
part no. of the missing part. The packaging
includes a silicate bag for absorbing moisture
during storage and transportation. Please
dispose of the bag once you have unpacked the
equipment.
The directions left, right, front and back are
defined as seen from the exercising position.
We recommend two persons for the assembly of
E4R.
HANDLEBAR ASSEMBLY AND SEAT
(version with hand grip pulse)
1.
Remove the seat fastening nuts.
2.
Place the seat upside down, for example, on a
chair.
3.
Place the handlebar, the spacer bar and the seat
frame upside down on the bottom of the seat. Do
not damage the hand grip pulse wires.
4.
Fasten the handlebar and seat to the seat frame
with nuts.
5.
Attach the hand grip pulse wires to the coiled
cable and push the extra length of wire inside the
handlebar.
6.
Fasten the locking knob (A) of the seat.
HANDLEBAR ASSEMBLY AND SEAT
(version without hand grip pulse)
1.
Remove the seat fastening nuts.
2.
Place the seat upside down, for example, on a
chair.
3.
Place the handlebar, the spacer bar and the seat
frame upside down on the bottom of the seat.
4.
Fasten the handlebar and seat to the seat frame
with nuts.
5.
Fasten the locking knob (A) of the seat.
LOWER FRAME
1.
Fasten the lower frame to the seat frame using
four M8x20 Allen screws (B) and washers (C).
Make sure that the seat beam is properly aligned
with the lower frame. Make sure the screws are
tightly fastened.
FEET
1.
Secure the rear foot with two M10 bolts (D)
and washers (E) to the lower frame. At this point
tighten the bolts only with your fingers.
2.
Lift the cycle on the floor and turn it right side
up.
3.
Fasten the front foot with the transportation
wheels to the front frame the same way.
JOINING THE FRAMES
1.
Remove the M5 screws in the front and seat
frames.
2.
Connect the handgrip pulse wires with the
connectors in the front frame.
3.
Join the front frame and seat frame by pushing
one tube inside the other so that the screw holes
in the tubes match together.
4.
Fasten the frames with two M8 screws (F) and
washers (C). Do not damage the hand grip pulse
wires.
5.
Secure the drink bottle rack in place with the
M5 screws.
6.
Tighten the rear and front foot screws.
7.
Push the plastic caps over the nuts.
SEAT BACK
1.
Push the fastening screw (G) through the hole
in the seat frame tube and the assembly plate.
2.
Place the bushing (H) on the fastening screw
and secure the plate by tightening the nut (I) on
the fastening screw.
3.
Remove the fastening nuts and washers of
the seat back and attach the seat back to the
assembly plate with them.
4.
Push the plastic caps over the nuts.