Top Innovations SF-432 - Manual (Page 3)

Top Innovations, Inc.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock, or injury, the
following basic safety precautions should always be followed when
using an electrical appliance.
SAVE THESE INSTRUCTIONS!
FOR HOUSEHOLD USE ONLY
READ ALL INSTRUCTIONS BEFORE USE
1. Use Fabric Steamer & Iron only for its intended purpose as indicated in this manual.
2. To reduce risk of contact with hot water emitting from steam vents, check appliance
before each use by holding it away from body and pressing Steam Button. Do not
operate unit if steam vents are blocked.
3. To protect against risk of electric shock, do not immerse unit in water or other liquids.
Do not use power cord or Steam Hose as handle, or allow them to be crimped.
4. Lighted On/Off Switch should always be set to “OFF” position before plugging or
unplugging unit from outlet. Never yank cord to disconnect from outlet; instead, grasp
plug and pull to disconnect.
5. Do not allow power cord to touch hot surfaces. Allow unit to cool completely before
putting away. Loop power cord loosely around unit when storing.
6. Always disconnect unit from electrical outlet when filling with water or emptying and
when not in use.
7. Do not operate iron with a damaged power cord or if the iron has been dropped or
damaged. To avoid risk of electrical shock, do not disassemble unit; take it to a
qualified service repair person for examination and repair. Incorrect reassembly can
cause a risk of electrical shock when unit is used.
8. Close supervision is required for any appliance being used near children, pets and plants.
Do not leave unit unattended while plugged in or on a table or ironing board.
9. Burns can occur from touching hot metal parts, hot water, or steam. Do not touch
Ironing Plate or attempt to connect Fabric Brush while unit is in use. Use caution when
you turn unit upside-down - there may be hot water in water reservoir.
10. If Heating Indicator Light does not illuminate, unit is not operating normally.
Immediately disconnect from power supply and have unit serviced by qualified service
personnel.
3
PROBLEM
Unit fails to heat up. Heating
Indicator Light does not
illuminate. Unit is not plugged in. Plug electrical cord into outlet.
Household Circuit Breaker /
Ground Fault Interrupter has
tripped or blown a fuse. Reset Circuit Breaker / Ground
Fault Interrupter, or replace fuse.
If you need assistance, contact a
licensed electrician.
Unit heats up, but fails to Steam.
Heating Indicator Light does
illuminate.
(Note: Allow proper time for unit
to heat up and begin producing
steam.)
Water reservoir is empty. Refill water reservoir using
procedures on page 10 of this
manual.
Mineral build-up in unit. Follow Removing Mineral
Build-Up procedure on page 13
of this manual.
Steam output is intermittent. Mineral build-up in unit. It is normal for unit to periodically
stop steaming for a few seconds.
If steam stays off for longer
periods, follow Removing
Mineral Build-Up procedure
on page 13 of this manual.
Steam Button not being pressed
continuously. For continuous steam, press and
hold Steam Button.
CUSTOMER SUPPORT
For problems with your Fabric Steamer & Iron, please refer to the troubleshooting solutions located
above. Additional inquiries should be directed to our Customer Support services through our Web
site,
www.SteamFast.com, on the Service Request Web page.
If you do not have internet access, you may also contact our Customer Support Department by
telephone, at (800) 711-6617 or (816) 584-9700.
NOTE: In order for our customer service representatives to help you as quickly and efficiently
as possible, please have the following information ready before calling:
• Purchase information (where and when you purchased this product)
• Product Serial Number
T ROUBLESHOOTING & C USTOMER S UPPORT
POSSIBLE CAUSE SOLUTION
14 Top Innovations, Inc.
Loud pumping sound when
Steam Button is pressed. Low water level in water
reservoir. Refill water reservoir using
procedures on page 10 of this
manual.
Steam Button is not being
pressed. Press and hold the Steam Button
for a few seconds for steam to
begin flowing.