Tapco Blend 6 - Manual (Page 15)

15
Appendix C: Blend 6 Specifi cations
Frequency Response
Mic Input to any Output (Trim at 0 dB):
+0, –1 dB,
20 Hz to 20 kHz
–3 dB,
10 Hz to 80 kHz
Distortion
THD and SMPTE IMD; 20Hz to 20kHz
Mic Input to Main Output:
< 0.025%
@ +4 dBu output
Noise
20 Hz to 20 kHz BW (150 Ω source impedance)
Equivalent Input Noise (EIN): –128 dBu
Residual Output Noise:
Channel and Main Mix levels off
Main, Ctrl Room, Phones:
–102 dBu
Aux 1 Mon out –82 dBu
Aux 2 FX out –92 dBu
Common Mode Rejection Ratio
(CMRR)
Mic In: 60 dB @ 1 kHz
Gain @ maximum
Crosstalk
Adjacent Inputs or Input to Output:
–85 dB @ 1 kHz
Input Gain Control Range
Mic In: +3 dB to +50 dB
Line In: –22 dB to + 25 dB
Phantom Power
+48 VDC
Equalization
Mono Channel EQ:
High
±15 dB @ 12 kHz
Low ±15 dB @ 80 Hz
Stereo Channel EQ:
High
±15 dB @ 12 kHz
Low ±15 dB @ 80 Hz
Mixer Rated Output
Main, Aux, Control Room: +4 dBu
Maximum Rated Output: +18 dBu
Maximum Input Levels
Mic Input: +18 dBu,
Gain @ +3 dB
Inst Input: +18 dBu,
Gain @ –22 dB
Stereo Line Input, Tape Input, and Aux Return:
+18 dBu
Maximum Voltage Gain
Mic Input to:
Main Output:
74 dB
Tape Output: 74 dB
Aux Sends: 74 dB
Control Room Output: 84 dB
Phones Output: 84 dB
Inst Input to:
Main Output:
49 dB
Tape Output: 49 dB
Aux Sends: 49 dB
Control Room Output: 59 dB
Phones Output: 59 dB
Stereo Line Input to:
Main Output:
20 dB
Tape Output: 20 dB
Aux Send: 20 dB
Control Room Output: 30 dB
Phones Output: 30 dB
Tape Input to:
Main Output:
10 dB
Tape Output: 10 dB
Control Room Output: 10 dB
Phones Output: 10 dB
Aux Return to:
Main Output:
20 dB
Tape Output: 20 dB
Aux Send: 20 dB
Control Room Output: 30 dB
Phones Output: 30 dB
Input Impedance
Mic Input: 2.3 k Ω, balanced
Inst Input: 1 M Ω
Stereo Line Input: 20 k Ω, balanced
Stereo Aux Returns: 20 k Ω, balanced
CD/Tape In: 24 k Ω, unbalanced
Output Impedance
Main, Ctrl Room, Aux Sends: 120 Ω
Tape Output: 1 k Ω
Phones Output: 25 Ω
Channel Level Set LED (Sensitivity)
0 dBu
(normal operating
level)
VU Meters
Main Left and Right
8 segments:
Clip (+16), +12, +8, +4, 0, –2, –4, –12, –24
0 LED = +4 dBu