Texas Instruments TSC2007EVM - Manual (Page 9)

www.ti.com
6.4.4 Datalogging
7 EVM Bill of Materials
EVM Bill of Materials
The two power-down bits of the TSC2007 can be set from this panel as well. A brief description of the
mode selected is shown on the screen when setting these bits; see Table 3 (Command Byte Definitions)
of the TSC2007 data sheet (
SBAS405 ) for details on what these bits do.
The software can record the data it takes from the TSC2007 to a tab-delimited file, suitable for importing
into spreadsheets. To do this, first go into the File menu, and select Log Data to File..., which opens a
file-select window and allows you to specify a file to which to write the data. At the same time, this enables
the Datalogging menu.
When ready to begin recording data to a file, select Datalogging
→
Start Logging. Data is written to the file
until Datalogging
→
Stop Logging is selected. When the screen is not touched, the AUX and TEMP values
are written to the file, and the X, Y, Z1, and Z2 parameters are written to the file with values of 9999, to
indicate that they are not updated. When the screen is touched, the X, Y, Z1, and Z2 parameters are
written while the AUX and TEMP values are written to the file as 9999. Because the program constantly
updates at a rate of about 400 readings per second, datalog files can quickly grow large; therefore, log
only that data which is necessary.
The format of the data file has the first column as the time in milliseconds (which is just a timer in the
program; it can arbitrarily start at any number), then X, Y, Z1, Z2, AUX, TEMP0, and TEMP1 columns.
Every new reading is a new row in the file.
Table 7 and Table 8 contain a complete bill of materials for the modular TSC2007EVM evaluation board
and the USB-MODEVM interface board, respectively (included only in the TSC2007EVM-PDK).
Table 7. TSC2007EVM Bill of Materials
Reference Designator Description Manufacturer Manufacturer's Part Number
R1 100
Ω
1/8W 5% Chip Resistor Panasonic ERJ-6GEYJ101V
R2, R3 2.7k
Ω
1/10W 5% Chip Resistor Panasonic ERJ-3GEYJ272V
R4 20k Ω 1/10W 5% Chip Resistor Panasonic ERJ-3GEYJ272V
C1, C3, C8 0.1µF 16V Ceramic Chip TDK C1608X7R1C105K
Capacitor, +/ - 10%, X7R
C2 10µF 16V Ceramic Chip TDK C3216X5R1C106M
Capacitor, +/ - 20%, X5R
C4-C7 Ceramic Chip Capacitor -
Not installed
U1 I 2 C Touch Screen Controller Texas Instruments TSC2007IZZZ
U2 64K I 2 C EEPROM MicroChip 24AA64-I/SN
TSC2007EVM PCB Texas Instruments 6486822
J1A, J2A 20-pin SMT plug Samtec TSM-110-01-L-DV-P
J1B, J2B 20-pin SMT socket Samtec SSW-110-22-F-D-VS-K
J3A 10-pin SMT plug Samtec TSM-105-01-L-DV-P
J3B 10-pin SMT socket Samtec SSW-105-22-F-D-VS-K
JMP2 2-position jumper , 0 .1" spacing Samtec TSW-102-07-L-S
JMP1 3-position jumper , 0 .1" spacing Samtec TSW-103-07-L-S
TP1 Miniature test point terminal Keystone Electronics 5000
TP2 Miniature test point terminal Keystone Electronics 5001
TP4, TP5, TP6, TP7 Miniature test point terminal Keystone Electronics 5002
TP8 Miniature test point terminal Keystone Electronics 5004
TP9, TP10, TP11 Miniature test point terminal Keystone Electronics 5003
Header shorting block Samtec SNT-100-BK-G-H
SLAU199 – March 2007 TSC2007EVM and TSC2007EVM-PDK User's Guide 9
Submit Documentation Feedback