Tannoy PASSIVE STUDIO MONITORS 6 - Manual (Page 10)

18 19
7.0: SERVICING 7.1: CABINET FINISH
To remove marks and scuffs use a soft brush. If necessary, a little warm water and detergent can be used but under no
circumstances use a solvent or abrasive cleaner.
7.2: DRIVER REMOVAL
Lay the cabinet on its back. Remove the ten hexagonal screws and set aside. Ease the driver from the front of the cabinet taking
care not to mark the front surface. Remove the driver, note the polarity of the internal connections and disconnect the internal
wiring. Take care not to damage the moving parts of the LF driver. To refit the driver, connect the cables from the crossover to
the LF terminals. Fit the driver into the mounting hole, making sure that the internal connecting cables are not trapped or able
to touch the LF cone. Fasten the screws finger tight and then progressively tighten them down with the appropriate Allen key.
Repeat the same procedure for the HF driver.
7.3: CROSSOVER
The crossover is mounted on the rear of the terminal panel. To inspect it, remove the panel by releasing the hexagonal screws.
Take care to avoid undue stress on the cables and components.
To remove the crossover completely the cables must be disconnected from the drive unit. Please proceed as above to remove
the drive unit.
6.0: REVEAL 66 TECHNICAL SPECIFICATIONS
Frequency response (1)
Recommended amplifier power
Power handling
Nominal Impedance
Sensitivity SPL / 1 W @ 1 m (3)
Distortion
Crossover frequency
Dispersion (@ -6dB)
Drive unit LF/MID
WideBand™ HF
Shielded
LOUDSPEAKER
57Hz – 51kHz
80 to 150 W rms into 8Ω
Average (2) 80W rms
Programme 160W
6Ω
92dB
< 0.6%
2.7kHz
90 degrees
200mm (8") multi fibre paper pulp cone
25mm (1") titanium dome neodymium magnet system
Yes
8.0: WARRANTY
NO MAINTENANCE OF THE REVEAL 66 MONITOR IS NECESSARY.
All components are guaranteed for a period of five years from the date of manufacture, subject to the absence of, or evidence
of, misuse, overload or accidental damage.
For further information please contact your dealer or the distributor in your country.
If you cannot locate your distributor please contact:
Customer Services, Tannoy Ltd., Coatbridge, Strathclyde, ML5 4TF, Scotland
Telephone: 01236 420199 (UK) +44 1236 420199 (International)
Fax: 01236 428230 (UK) +44 1236 428230 (International)
Internet: http://www.tannoy.com
DO NOT SHIP ANY PRODUCT TO TANNOY WITHOUT PREVIOUS AUTHORISATION
This warranty in no way affects your statutory rights.
7.4: LIST OF SPARE PARTS
PART NUMBER DESCRIPTION
Driver Kit
High Frequency Unit
Passive Crossover
Further spare part details and factory part numbers can be found at www.tannoy.com
(1) /- 3 dB, measured at 1m in an anechoic chamber. (2) Long term power handling capacity as defined in EIA standard RS426A.
(3) Averaged over specified bandwidth for half-space environment.
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications which Tannoy reserve the right to alter without
prior notice. Please verify the latest specifications when dealing with critical applications.
NOTES
Low frequency design
Cabinet construction
Cabinet finish
Fittings
Cabinet dimensions (HxWxD)
Total Cabinet weight
CABINET
Optimised bass-reflex loaded
MDF cabinet and front baffle, Tongue and groove front and back
Maroon satin texture finish front, Grey vinyl sides and back
4 x M6 inserts for Omnimount™ 30 series bracketry
230mm (9”) x 527mm (20 3 / 4 ”) x 340mm (13 3 / 8 ”)
12.8kg (28.16lbs)
Type 1603 -7900 0747
Type 0294 – 7900 0891B
Type 1465 – 7300 0938
9.0: DECLARATION OF CONFORMITY
The following apparatus is/are manufactured in China for Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5
4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives
relevant to Domestic Electrical Equipment. The apparatus is designed and constructed such that electromagnetic disturbances
generated do not exceed levels allowing radio and telecommunications equipment and other apparatus to operate as intended,
and, the apparatus has an adequate level of intrinsic immunity to electromagnetic disturbance to enable operation as specified
and intended.
This equipment conforms to the requirements of the EMC Directive 89/336/EEC, amended by 92/31/EEC and 93/68/EEC and
the requirements of the Low Voltage Directive 73/23/EEC, amended by 93/68/EEC.
Details of the Apparatus: Tannoy Monitor Loudspeaker
Model Number: Reveal 66
Applicable Standards: EN55103-1:1996 Emission
EN55103-2:1996 Immunity
Electrical Safety EN60065:1993
Signed:
Position: Technical Director
Date: 1 March 2005
For Tannoy Ltd