Transition Networks C/E-100BTX-FRL-03 - Manual

The TRANSITION Networks 100BASE-TX to 100BASE-FX slide-in-module media
converters,
C/ E-100BTX-FRL-03, C/ E-100BTX-FRL-03(SC) and C/ E-100BTX-FRL-03(SM),
which are designed to be installed in the TRANSITION Networks Media Conversion
Center,
E-MCC-1600 , connect 100BASE-TX unshielded twisted pair cable to 100BASE-
FX multimode OR singlemode fiber-optic cable. All media converters function in half-
duplex mode or, when connected to devices capable of full-duplex connectivity, in full-
duplex mode. An MDI/MDI-X switch allows straight-through twisted-pair cable to be
used for crossover 100BASE-TX connections.
Minneapolis, MN 55344 USA
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Compliance Information
UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class B
FCC Regulations
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.
Canadian Regulations
This digital apparatus does not exceed the Class B limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.
Copyright Restrictions
© 1998, 1999 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.
Trademark Notice
All registered trademarks and trademarks are the property of their respective owners. 33044.C
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten
verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur
Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen
einschliesslich der gegenseitigen Anerkennung ihrer Konformität.
MEDIA CONVERTER TECHNICAL SPECIFICATIONS
Standards IEEE 802.3u
Environment Temperature: 0-40°C (32° to 104° F )
Humidity 10-90%, non condensing
Altitude 0-10,000 feet
Warranty Five years
100BASE-TX/100BASE-FX
Slide-In-Module Media Converters
C/E-100BTX-FRL-03, C/E-100BTX-FRL-03(SC), C/E-100BTX-FRL-03(SM)
USER’S GUIDE
100BASE-FX
Multimode
Fiber
100BASE-TX
Copper
C/E-100BTX-FRL
-03
P
100BASE-FX
100BASE-TX
Fast Ethernet TM
C/100BTX-FRL-03
100BASE-FX
Multimode
Fiber
100BASE-TX
Copper
C/E-100BTX-FRL
-03
P
100BASE-FX
100BASE-TX
Fast Ethernet TM
C/100BTX-FRL-03(SC)
100BASE-FX
Singlemode
Fiber
100BASE-TX
Copper
C/E-100BTX-FRL
-03
P
100BASE-FX
100BASE-TX
Fast Ethernet TM
C/100BTX-FRL-03(SM)
C/E-100BTX-FRL-03
Provides an RJ-45 twisted pair 100BASE-TX
connector and a set of RX (receive) and TX
(transmit) ST 100BASE-FX connectors to
multimode fiber-optic cable.
C/E-100BTX-FRL-03(SC)
Provides an RJ-45 twisted pair 100BASE-TX
connector and an RX (receive) and TX
(transmit) SC 100BASE-FX connector to
multimode fiber-optic cable.
C/E-100BTX-FRL-03(SM)
Provides an RJ-45 twisted pair 100BASE-TX
connector and an RX (receive) and TX
(transmit) SC 100BASE-FX connector to
singlemode fiber-optic cable.
Power Illuminated green LED indicates connection to external
AC power.
SDF Signal Detect/Fiber: Steady green LED indicates fiber port
is connected to device.
SDC Signal Detect/Copper: Steady green LED indicates RJ-45
port is connected to device.
RXC Receive/Copper: Flashing green LED indicates packets
are seen on RJ-45 port.
RXF Receive/Fiber: Flashing green LED indicates packets are
seen on fiber port.
P
E-FX
100BA
Status LEDs
Straight-through Cable Configuration
Straight-through/crossover 100BASE-TX requirements are satisfied using the
MDI/MDI-X switch with straight-through cable.
The two active pairs in a 100BASE-TX
network are pins 1 & 2 and pins 3 & 6.
Use only dedicated wire pairs (such as
blue/white & white/blue, orange/white &
white/orange) for the active pins.
1
2
3
6
Twisted
Pair #1
Twisted
Pair #2
Straight Through Cable
1
2
3
6