Tricity Bendix AW 1560 W - Manual (Page 6)

6
1 Detergent dispenser drawer
Programme Option buttons
Depending on the programme, different functions can
be combined. These must be selected after choosing the
desired programme and before depressing the “start
pause” button.
When these buttons are pressed, the corresponding pilot
lights come on. When they are pressed again, the pilot
lights go out.
If an incorrect option is selected, the corresponding
pilot light flashes for about 2 seconds.
2 8 H and 4 H button
You can press this button to delay the start of the
washing programme by 8 or 4 hours. The delay you
have selected is indicated by the illumination of the
corresponding light.
You must select this option after you have set the
programme and before you press the START
PAUSE button.
You can cancel the delay time at any moment, before
you press the START/PAUSE button.
If you have already pressed the START/PAUSE button,
and you wish to cancel the delay time, proceed as
follows:
• set the washing machine to PAUSE by pressing the
START/PAUSE button;
• press the DELAY button once, the light relevant to the
selected delay goes off .
• press the START/PAUSE button again to start the
programme.
Important!
● The selected delay can be changed only after
selecting the washing programme again.
● The door will be locked throughout the delay time.
If you need to open the door, you must first set the
washing machine to PAUSE by pressing the
START/PAUSE button. After you have closed the
door, press the START/PAUSE button again.
The Control Panel
6kg load
AW 1560 W
PROGRAMME
1 2 3 6 5 4 7 8
prewash/wash
rinses
spin
drain
end
4 H
8 H
spin reduction rinse hold start pause
1
4
5
6
7 8
2
3
10
13
9
15
12
14
11
WHITES with prew.
FAST COLOURS
NON FAST COLOURS
SYNTHETICS
DELICATES
Rinses
Spin
Drain
Softeners
HANDWASH
WOOL
Mini Program
SYNTHETICS Easy Iron
COLOUR CARE
WHITES economy
95°
60°
40°
50°
40°
30°
40° 2
3
4
5
6
10
11
12
13
14
15
40°
30°
60°
1
7
8
9
half load
ELECTRONIC 1500
The delay start can not be selected with SPIN and
DRAIN programmes.
3 Rinse Hold button
When selecting this option the water of the last rinse is
not emptied out, to prevent the fabrics from creasing.
At the end of the programme the pilot lights “door” and
“end” illuminate. To drain water, proceed as follows:
● turn the programme selector dial to position “O”;
● select programme 8 (drain) or 7 (spin). In this case
reduce the spin speed by means of the relevant
button to adapt it to the fabrics to be spun.
● press “start pause” button.
4 Spin Reduction button
By selecting this option the speed will be reduced as
follows:
Cotton: from 1500 to 700 r.p.m. and from 1200 to 600
r.p.m.
Synthetics, wool and handwash: from 900 to 450
r.p.m.
Delicates: from 700 to 450 r.p.m.
5 Half Load button
Select this button to reduce water consumption on the
rinse cycle when washing a smaller load of cottons or
linens (maximum load size = 3 kg).
The machine will perform 2 rinses instead of 3.
6 Start Pause button
After having selected the required programme, press
this button to start the machine; the corresponding pilot
light stops flashing.
To interrupt a programme which is running, depress the
“start pause” button: the corresponding pilot light starts
to flash.
To restart the programme from the point at which it was
interrupted, press the “start pause” button again.
132991640.qxd 06/10/2003 17:08 Pagina 6 (Nero/Process Black pellicola)