Yamaha DB50XG - Manual (Page 13)

12
2.1.4.2 XG System Data parameter change
See tables <1 - 1> and <1 - 2> (page 27).
2.1.4.3 Multi Effect1 Data parameter change
See tables <1 - 1> and <1 - 3> (page 27).
2.1.4.4 Multi Part Data parameter change
See tables <1 - 1> (page 27) and <1 - 4> (page 28).
2.1.4.5 Drums Setup Data parameter change
See tables <1 - 1> (page 27) and <1 - 5> (page 30) .
If a Drum Setup Reset parameter change message (page 27)
is received, the Drum Setup parameter values will be ini-
tialized.
Selecting a Drum Set will cause the Drum Setup parameter
values to be initialized.
2.1.5 Other parameter changes
2.1.5.1 Master Tuning
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0001nnnn 1n Device Number
00100111 27 Model ID
00110000 30 Sub ID2
00000000 00
00000000 00
0mmmmmmm mm Master Tune MSB
01111111 11 Master Tune LSB
Occccccc cc irrelevant
11110111 F7 End of Exclusive
This message simultaneously changes the pitch of all chan-
nels.
2.2 Bulk Dump
The DB50XG receives the following bulk dump data.
[ XG NATIVE ]
1) XG System Data
2) Multi Effect1 Data
3) Multi Part Data
4) Drums Setup Data
[ QS300 NATIVE ]
1) QS300 User Normal Voice Data
2.2.1 XG Native Bulk Dump
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0000nnnn 0n Device Number
01001100 4C XG Model ID
0bbbbbbb bb ByteCount
0bbbbbbb bb ByteCount
0aaaaaaa aa Address High
0aaaaaaa aa Address Mid
0aaaaaaa aa Address Low
0ddddddd dd Data
| |
| |
0ccccccc cc Check-sum
11110111 F7 End of Exclusive
For the Address and Byte Count, refer to the supplementary
tables.
The Check Sum is the value that results in a value of 0 for
the lower 7 bits when the Start Address, Byte Count, Data,
plus the Check Sum itself are added.
2.2.1.1 XG System Data bulk dump
See tables <1 - 1> and <1 - 2> (page 27).
2.2.1.2 Multi Effect1 Data bulk dump
See tables <1 - 1> and <1 - 3> (page 27).
2.2.1.3 Multi Part Data bulk dump
See tables <1 - 1> (page 27) and <1 - 4> (page 28).
2.2.1.4 Drums Setup Data bulk dump
See tables <1 - 1> (page 27) and <1 - 5> (page 30).
2.2.2 QS300 Native Bulk Dump
Up to 32 Voices created by the QS300 can be saved in the
DB50XG’s User Memory by bulk dump messages. (Effective
only when the XG mode is active.)
QS300 User Voices are stored in Bank MSB = 63, LSB = 00.
Program Change numbers for User Voices are 1 – 32.
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0000nnnn 0n Device Number
01001011 4B QS300 Model ID
0bbbbbbb bb ByteCount
0bbbbbbb bb ByteCount
0aaaaaaa aa Address High
0aaaaaaa aa Address Mid
0aaaaaaa aa Address Low
0ddddddd dd Data
| |
| |
0ccccccc cc Check-sum
11110111 F7 End of Exclusive
* Because of possible differences in number of elements, some
QS300 Voices may sound slightly different.
2.2.2.1 QS300 User Normal Voice Data bulk dump
See tables <2 - 1> and <2 - 2> (page 30).
3. REALTIME MESSAGES
3.1 Active Sensing
Once FE has been received, if no MIDI data is subsequently
received for longer than an interval of approximately 300msec,
the DB50XG will perform the same function as when ALL
SOUNDS OFF, ALL NOTES OFF, and RESET ALL CON-
TROLLERS messages are received, and will then return to a
status in which FE is not monitored.
MIDI Data Format