Yamaha GX-500VCD - Manual (Page 20)

E-12
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 0
TIME PROG R. TIME
C
EDIT +10
D
PRESET
E
MODE REPEAT RANDOM TUNER
SELECT RETURN TIME INDEX
DISC SKIP
DIRECTION DIGEST KARAOKE INTRO
A B
TAPE
TUNER
VCD / CD
REC/PAUSE
DISC 1 DISC 2 DISC 3
DOWN UP
VOLUME
STANDBY/ON
DIRECTION
YMERSION B.BOOST MUSIC INPUT INPUT
MIN
PRESET/ TUNING/ BAND A/B/C/D/E
DISC CHANGE OPEN / CLOSE
AUTO/MANUAL
TIMER
MEMORY
TIME ADJ
REC/PAUSE DOLBY NR
HOUR
RANDOM REPEAT TIME
DISPLAY MODE
KARAOKE
CD/Video CD player operation
Program play
You can program up to 20 tracks in any desired order.
1
When the CD/Video CD player is stopped, press PROG to
prepare for programming.
* “PROG” (
A
) and “P-01” (
2
) will light up on the display,
and all track numbers on the selected disc (
9
) will begin
flashing.
2
If necessary, select the desired disc by pressing DISC SKIP.
* Just after you change the disc, the CD/Video CD player
reads the contents of the newly selected disc for a few
seconds. During this internal operation, if you go on to the
next step, “WAIT” (
2
) appears on the display and your
operation is canceled.
3
Use the numeric buttons to select the desired
track number.
* The selected track number (
1
) and the total play time of
the programmed tracks (
2
) will light up on the display,
and soon it will be replaced by the display of the next play
order (
2
). Programmed track numbers on the selected
disc will stop flashing and light up on the music calendar
(
9
).
* Pressing TIME displays the total play time of the
programmed tracks (
2
) for about 1 second, and then it
is replaced by the display of the next play order (
2
).
4
Repeat steps 2 and 3 to program other tracks.
5
Press / to start the program play.
Notes
●
When the CD/Video CD player is in the Playback Control
mode (“PBC” (
5
) is illuminated on the display) and the play
is stopped, pressing PROG cancels the Playback Control
mode, and so you can make programming operations.
● If the total time of the programmed tracks becomes 100
minutes or more, the highest position of the figure will not be
displayed.
● The total time of the programmed tracks will not be
displayed, if track number 16 or higher is programmed.
● Skip ( / ) can be performed during play, but only
within the range of the programmed tracks.
● Search can be performed during play to search all tracks,
including unprogrammed tracks.
1
2 5
TIME
3
TIME
5
Display information during programming
Music calendar
Play order Selected disc
Total playing time Selected track number
KK
AM
C HALL
YMERSION
EDIT
PROG
S F REP
VOLUME A B OVER 15
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
TRACK
VCD PBC
TIMER
SLEEP
NOR TEST
PHANTOM
RANDOM TUNER
CD
MD
TAPE
AM
C HALL
YMERSION
EDIT
PROG
S F REP
VOLUME A B OVER 15
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
TOTAL
TRACK
VCD PBC
TIMER
SLEEP
NOR TEST
PHANTOM
RANDOM TUNER
CD
MD
TAPE
K K
To cancel a programmed sequence
There are several methods as described below.
● Press while the CD/Video CD player is stopped.
● Open the disc tray.
● Turn this system into the standby mode.
To check (and correct) program data
1. Press PROG when the CD/Video CD player is stopped.
2. Every time
is pressed, the track numbers and
sequential order of the programmed tracks can be checked
one after another. The display of the track number can be
returned (sequentially in reverse order) by pressing
.
3. If you want to correct the program data, press a numeric
button to select the track to replace the one displayed. The
previously programmed track will be cleared from the
memory and the new one will be programmed.
To complete the correction, press PROG or
/ once
again.
For Video CDs