Midi data format, Clp-970 – Yamaha CLP-970M EN User Manual
Page 27
CLP-970
27
2.2.1 XG bulk dump
This message sets XG-related parameters. Unlike parameter change messages, a single
message can modify multiple parameters. The message format is as follows.
11110000
F0H
Exclusive status
01000011
43H
YAMAHA ID
0000nnnn
0NH
N:Device Number
01001100
4CH
Model ID
0sssssss
SSH
ByteCountMSB
0ttttttt
TTH
ByteCountLSB
0ggggggg
GGH
Address High
0mmmmmmm
MMH
Address Mid
0lllllll
LLH
Address Low
0vvvvvvv
VVH
Data
:
:
0kkkkkkk
KKH
Check-sum
11110111
F7H
End of Exclusive
Address and Byte Count are given in tables 1-n. Byte Count is indicated by the total
size of the Data in tables 1-n.
Bulk dump and dump request messages are received when the beginning of the block
is specified as the 'Address'.
'Block' indicates the unit of the data string that is indicated in tables 1-n as 'Total size'.
Check sum is the value that produces a lower 7 bits of 0 when the Start Address, Byte
Count, Data, and the Check-sum itself are added.
2.2.1.1 XG System bulk dump
This message sets the XG SYSTEM block (refer to tables <1 -1>, <1 - 2>).
2.2.1.2 Multi Effect1 bulk dump
This message sets the MULTI EFFECT1 block (refer to tables <1 - 1>,
<1 - 3>).
2.2.1.3 Multi Part bulk dump
This message sets the MULTI PART block (refer to tables <1 - 1>, <1 - 4>).
2.2.1.4 Drums Setup bulk dump
This message sets the DRUMS SETUP block (refer to tables <1 - 1>, <1 - 5>).
3. Realtime messages
3.1 Active sensing
a) Transmission
not transmitted.
b) Receive
Once FE has been received, failure to receive any MIDI message for an interval
longer than approximately 300 msec will cause processing to be performed as if
ALL SOUND OFF, ALL NOTE OFF, and RESET ALL CONTROLLERS mes-
sages were received, and the unit will reset to a condition in which FE was never
received.
< Table 1-1 >
< Table 1-2 >
MIDI Parameter Change table ( XG SYSTEM )
Address
Size
Data
Parameter
Description
Default value
(H)
(H)
(H)
(H)
00 00 00
4
00 - 0F
MASTER TUNE
-102.4...0...+102.3[cent]
00 04 00 00
01
00 - 0F
1st bit3-0
→
bit15-12
02
00 - 0F
2nd bit3-0
→
bit11-8
03
00 - 0F
3rd bit3-0
→
bit7-4
4th bit3-0
→
bit3-0
04
1
00 - 7F
MASTER VOLUME
0...127
7F
05
1
not used
06
1
28 - 58
TRANSPOSE
-24...0...+24[semitones]
40
7D
1
N
DRUM SETUP RESET
N: Drum setup number(0,1)
--
7E
1
00
XG SYSTEM ON
00=XG system ON (receive only)
--
7F
1
00
ALL PARAMETER RESET
00=ON (receive only)
--
TOTAL SIZE
07
Parameter Base Address
MODEL ID = 4C
Parameter
Description
Address
(H)
(M)
(L)
XG SYSTEM
00
00
00
System
00
00
7D
Drum setup Reset
00
00
7E
XG System On
00
00
7F
All Parameter Reset
EFFECT 1
02
01
00
Effect1(Reverb,Chorus,Variation)
MULTI PART
08
:
08
00
:
0F
00
:
00
Multi Part 1
:
Multi Part 16
DRUM
30
31
0D
0D
00
00
Drum Setup 1
Drum Setup 2
Address
Parameter
3n
0D
00
note number 13
3n
3n
0E
:
5B
00
00
note number 14
:
note number 91