Speaker balance adjustment, E-16 adjustments, Before operation – Yamaha EMX120CD User Manual

Page 24: Time adj timer hour min, Soft normal max min echo echo, Press the standby/on switch to turn the power on, Tape/md ld/tv audio signal vcr subwoofer, Normal phantom

Advertising
background image

CD CHANGER RECEIVER EMX–120CD

PRESET/TUNING/BAND

A/B/C/D/E

OPEN/CLOSE

DISC

1

DISC

2

DISC

3

DISC

CHANGE

VOLUME

INPUT SELECTOR

VCR•LD/TV•CD•TAPE/MD•TUNER

CD

TUNER

STANDBY/ON

PHONES

KARAOKE

PROGRAM

MEMORY

MUSIC

DISPLAY

MEMORY

AUTO/MAN’L

REPEAT

TIME

TIME ADJ

TIMER

HOUR

MIN

INPUT TRIM

MIC TONE

MIC

MIC MIXING

SOFT

NORMAL

MAX

MIN

ECHO

ECHO

TIME

A

PROG

B

C

D

+

I0

E

CD

TUNER

1

1

2

2

3

3

4

4

5

5

6

6

7

7

8

8

9

0

PRESET

INPUT

MUSIC

PROGRAM

STANDBY/ON

DISPLAY

SLEEP

ECHO

FLAT

LEVEL

KARAOKE

VOLUME

DISC SKIP

STOP

PLAY/PAUSE

TUNER

CD

TEST

CENTER/REAR

/DELAY

OPEN/CLOSE

REPEAT

RANDOM

MODE

E-16

ADJUSTMENTS

Speaker balance adjustment

This procedure lets you adjust the sound output level balance
between the front, center, and rear speakers using the built-in
test tone generator. When this adjustment is performed, the
sound output level heard at the listening position will be the
same from each speaker. This is important for the best
performance of the built-in Dolby Pro Logic surround decoder.
The adjustment of each speaker output level should be
done at your listening position with the remote control
transmitter. Otherwise, the result may not be satisfactory.

Before operation

Set the CENTER MODE switch on the rear panel of this unit
to the position suitable for your speaker system configuration.
(Refer to page 7 for details.)

NORMAL (For 5-speaker configuration):

Select this position when you use the center speaker.

PHANTOM (For 4-speaker configuration):

Select this position when you do not use the center
speaker. The center sound will be output from the left
and right front speakers.

1

Press the STANDBY/ON switch to turn the power on.

2

Turn the VOLUME control counterclockwise to decrease
the volume to minimum.

3

Press the PROGRAM button once or more so that “
PRO LOGIC” lights up on the sound field program
indicator.

4

Press the TEST button.
* “TEST” flashes on and off on the display.

5

Press the VOLUME + (up) button to increase the volume.

You will hear a test tone (like pink noise) from the left front
speaker, then the center speaker, then the right front
speaker, and then the rear speakers, for about two seconds
each. The display changes as shown below.

* The test tone from the left rear speaker and the right rear

speaker will be heard at the same time.

(L and R)

4

2

3

1

5

1

2, 5

3

SPEAKERS

CENTER/REAR

SPEAKERS

FRONT

MAINS

R

L

CENTER

REAR

REAR

REAR SINGLE

CENTER

:6

MIN./SPEAKER

6

MIN./SPEAKER

SEE OWNER’S MANUAL FOR CONNECTION.

SEE OWNER’S MANUAL FOR CONNECTION.

REAR

:4

MIN./SPEAKER

REAR SINGLE :8

MIN./SPEAKER

R

L

L

AUDIO SIGNAL

TAPE/MD

LD/TV

AUDIO SIGNAL

VCR

SUBWOOFER

R

IN

OUT

IN

OUT

OUT

VCR

MONITOR

OUT

LD/TV

VIDEO SIGNAL

ANTENNA

AM

FM

GND

75

UNBAL.

IN

OUT

VIDEO SIGNAL

50kHz

9kHz

10kHz

100kHz

FM

AM

FREQUENCY

STEP

CENTER

MODE

NORMAL

PHANTOM

AC OUTLET

UNSWITCHED

100W MAX.

VOLTAGE

SELECTOR

NORMAL

PHANTOM

CENTER

MODE

Advertising