Yamaha GX-90VCD - Manual (Page 29)

E-19
English
1
1
2
2
3
3
4
4
5
5
+ I0
E
6
6
7
7
8
8
9 0
CD
PRESET
1
1
2
2
3
3
4
4
5
5
TIME
A
DISC SKIP
PROG
B
TAPE
C
EDIT
D
+ I0
E
OPEN/CLOSE INDEX MODE
6
6
7
7
8
8
9 0
CD
PRESET
TUNER
TAPE
RETURN
STOP PLAY PLAY REC/PAUSE TAPE 1/2
MUSIC
TEST FLAT CENTER/REAR
/DELAY
PROGRAM USER
POWER
INPUT SLEEP
VOLUME
REPEAT
PREV NEXT SELECT
ECHO/KEY
LEVEL
VIDEO-CD PLAYER OPERATION
Direct operation
When the power is off (in the standby mode), pressing the
CD input selector button or the DISC selector (1, 2 or 3)
button will turn the power on and start disc playback
automatically.
When the power is on, even if an input source other than
Video-CD player is selected, pressing a DISC selector button
or closing the disc table by pushing the front edge of the disc
table gently will start playback directly. In this case, if the
tape deck is playing back a tape, it will be stopped
automatically.
* These ways of playback can also be used to close the disc
table. If the table is closed in these ways, playback will
begin automatically, however, the display will not show the
total number of tracks and the total playing time of the disc
to be played back.
PLAYXCHANGE
During playback, you can open the disc table by pressing the
DISC CHANGE button without interrupting playback.
However, in this case, pressing the DISC SKIP button or a
DISC selector button has no effect.
Precautions
• If TV or radio interference occurs during Video-CD player
operation, move the unit away from the TV or radio.
• Subjecting the unit to shock or vibration can cause
mistracking.
• Playing back some discs at high volume can cause
mistracking. In this case, listen at lower volume.
• Do not pull open the disc table forcibly with your hands.
• Do not push the disc table while it is moving.
•
If the power fails while the table is open, wait until the
power supply returns or gently push the table manually to
close it.
•
The temperature range for playing back discs is
recommended to be 5°C (41°F) – 35°C (95°F).
Direct-selection playback
By using the track number input buttons on the remote
control transmitter, any track you wish to listen to can be
played back directly.
Use the track number input buttons to select the desired
track number. Playback will begin automatically.
A. For example, to choose selection 5
Press the “5” button.
B. For example, to choose selection 12
(1) Press the “+10” button.
(2) Within 3 seconds, press “2” button.
C. For example, to choose selection 20
(1) Press the “+10” button.
(2) Within 3 seconds, press the “+10” button again.
(3) Within 3 seconds, press the “0” button.
Note
If you select a track number higher than the number of tracks
on the disc, playback will begin from the last track on the
disc.
For easier operation
Pressing the DISC selector button (1, 2 or 3) will select the
disc directly, and playback will begin from track 1
automatically.
Note
If a Video-CD, version 2.0 is selected, “PBC” lights up on the
display, and the total number of tracks, the total playing time
of the disc and the music calendar will not be displayed. In
this mode, disc playback is controlled by the rule of Playback
Control. (For details of Playback Control, refer to page
25–27.)
To cancel this mode and restore the normal playback mode,
press and hold the stop
(RETURN) button for more than 2
seconds. “PBC” disappears from the display.
To call the Playback Control mode again, press and hold the
stop
(RETURN) button for more than 2 seconds.
To interrupt playback
1
Press the play/pause / button.
* The “ ” indicator will flash.
2
Press the play/pause / button to resume playback
from the same point.
To stop playback
Press the stop button.
To switch the unit off after use
Turn the unit off by pressing the POWER switch. (The
indicators will go off except for the current time display.)