Yamaha AN1x User Manual
Page 13
13
RPN
Not assigned; no change
PORTAMENTO SWITCH
0 (Off)
FOOT CONTROLLER
0 (Minimum)
RIBBON X CONTROLLER
64 (No effect)
RIBBON Z CONTROLLER
0 (Minimum)
VOLUME
127 (Maximum)
PAN
64 (No effect)
REVERB DEPTH
127 (Maximum)
CHORUS(VARIATION) DEPTH
No change
DELAY DEPTH
127 (Maximum)
(3-2-3) ALL NOTE OFF
(CONTROL NUMBER = 7BH , DATA VALUE = 0)
All the notes currently set to on in a certain channel are muted when receiving this message. However, if Hold 1 or Sostenute is on, notes
will continue sounding until these are turned off.
(3-2-4) OMNI MODE OFF
(CONTROL NUMBER = 7CH , DATA VALUE = 0)
Performs the same function as when receiving ALL NOTES OFF.
(3-2-5) OMNI MODE ON
(CONTROL NUMBER = 7DH , DATA VALUE = 0)
Performs the same function as when receiving ALL NOTES OFF. Not to change to OMNI ON.
(3-2-6) MONO
(CONTROL NUMBER = 7EH , DATA VALUE = 0)
Performs the same function as when receiving ALL SOUNDS OFF. If the 3rd byte (mono) is within 0 through 16, the channel will be
Mode4 (m = 1).
(3-2-7) POLY
(CONTROL NUMBER = 7FH , DATA VALUE = 0)
Performs the same function as when receiving ALL SOUNDS OFF. The channel will be Mode3.
(3-3) REGISTERED PARAMETER NUMBER
STATUS
1011nnnn(BnH)
n = 0 ~ 15; MIDI RECEIVE CHANNEL
LSB
01100100(64H)
RPN LSB
0ppppppp
p = RPN LSB(See chart below)
MSB
01100101(65H)
RPN MSB
0qqqqqqq
q = RPN MSB(See chart below)
DATA ENTRY MSB
00000110(06H)
DATA VALUE
0mmmmmmm
m = Data Value
DATA ENTRY LSB
00100110(26H)
DATA VALUE
0lllllll
l = Data Value
First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB.
RPN D.ENTRY
LSB MSB MSB LSB
PARAMETER NAME
DATA RANGE
00H 00H mmH ---
PITCH BEND SENSITIVITY
00H - 18H (0 - 24 semitones)
7FH 7FH --- ---
RPN RESET
Cancels RPN numbers
The internal value is not affected.
(3-4) SYSTEM REAL TIME MESSAGES
(3-4-1) ACTIVE SENSING
STATUS
11111110
(FEH)
Transmitted every 260 msec.
Once this code is received, the AN1x starts sensing. When no status data is received for over approximately 360 ms, MIDI receiving buffer will
be cleared, and the sounds currently played and the sustain switch are forcibly turned off. In this case, each control data will be reset to a certain
value.
(3-4-2) TIMING CLOCK(Receive only)
STATUS
11111000
(F8H)
Selects whether the tempo clock of the Arpeggiator, Step Sequencer and FreeEG is controlled by internal clock or the timing clock of an external
device via MIDI.
(3-5) SYSTEM EXCLUSIVE MESSAGE
(3-5-1) UNIVERSAL NON REALTIME MESSAGE
(3-5-1-1) IDENTITY REQUEST (Receive only)
F0H 7EH 0nH 06H 01H F7H
(3-5-1-2) IDENTITY REPLY (Transmit only)
F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH 00H 00H 00H vvH F7H
dd;Device Number Code@AN1x: 1A 02
vv;TG Support Level AN1x: 7E
(3-5-2) UNIVERSAL REALTIME MESSAGE
(3-5-2-1) MIDI MASTER VOLUME
F0H 7FH 7FH 04H 01H llH mmH F7H
Sets the MASTER VOLUME value.
The value mm is used to set the master volume (the value ll will be ignored).
(3-5-3) PARAMETER CHANGE
(3-5-3-1) DX1 MASTER TUNING
F0H 43H 1nH 04H 40H ddH F7H
When AN1x receives the DX1 compatible format, MASTER TUNE in the System Data will be changed.
The value “dd” is used to set the master tuning.
dd = -64(00H) ~ 0(40H) ~ +63(7FH)
(3-5-3-2) PARMETER CHANGE
11110000
F0
Exclusive status
01000011
43
YAMAHA ID
0001nnnn
1n
device Number
01011100
5C
Model ID
0aaaaaaa
aaaaaaa
Address High
0aaaaaaa
aaaaaaa
Address Mid
0aaaaaaa
aaaaaaa
Address Low
0ddddddd
ddddddd
Data
|
|
11110111
F7
End of Exclusive
For parameters with data size of 2, transmit the appropriate number of data bytes.
See MIDI Data Table for Address and Byte Count.
The following six types of data are transmitted/received.
System Data
Current Voice Common Data
Current Voice Scene1 Data
Current Voice Scene2 Data
Current Voice Scene Ctrl Data
Current Step SEQ Data
(3-5-4) BULK DUMP
11110000
F0
Exclusive status
01000011
43
YAMAHA ID
0000nnnn
0n
device Number
01011100
5C
Model ID
0bbbbbbb
bbbbbbb
ByteCount
0bbbbbbb
bbbbbbb
ByteCount
0aaaaaaa
aaaaaaa
Address High
0aaaaaaa
aaaaaaa
Address Mid
0aaaaaaa
aaaaaaa
Address Low
00000000
00
Data
|
|
0ccccccc
ccccccc
Check-sum
11110111
F7
End of Exclusive
See MIDI Data Table for Address and Byte Count.
The Check sum is the value that results in a value of 0 for the lower 7 bits when the Byte Count, Start Address, Data and Check sum itself are
added.
The following eight types of data are transmitted/received.
System Data
Current Voice Common Data
Current Voice Scene1 Data
Current Voice Scene2 Data
Current Voice Scene Ctrl Data
Current Step SEQ Data
User Voice Data
User Step SEQ Data
(3-5-5) DUMP REQUEST
11110000
F0
Exclusive status
01000011
43
YAMAHA ID
0010nnnn
2n
device Number
01011100
5C
Model ID
0aaaaaaa
aaaaaaa
Address High
0aaaaaaa
aaaaaaa
Address Mid
0aaaaaaa
aaaaaaa
Address Low
11110111
F7
End of Exclusive
See MIDI Data Table for Address and Byte Count.
The following eight types of data are received.
System Data
Current Voice Common Data
Current Voice Scene1 Data
Current Voice Scene2 Data
Current Voice Scene Ctrl Data
Current Step SEQ Data
User Voice Data
User Step SEQ Data
(4) CONFIGURATION OF KEYBOARD, ARPEGGIATOR AND TONE GENERATOR
+-----------+
+--------------+
|
MIDI IN
|
|
KEYBOARD
|
+-----------+
+--------------+
|
|
V
|
[Receive Channel]
|
|
|
V
V
+----------->+<--[LOCAL SW]<----+---------------------------------+
|
|
|
|
|
|
V
|
|
|
[LOCAL SW]
|
|
|
|
|
|
V
|
|
|
+---------------+
|
|
|
|ARPEGGIATOR/ |
|
|
|
| STEP SEQUENCER|
|
|
|
+---------------+
|
|
|
|
|
|
|
+-------------------|----------------+
|
|
|
|
|
|
|
|
|
[PATTERN
|
V
V
V
Transmit Channel]
|
+------------+-------------------+
|
|
|
|
[Transmit Channel]
|
|
|
|
+---------------+
|
|
V
V
+-----------------------+
+-------------------+
|
TONE GENERATOR
|
|
MIDI OUT
|
+-----------------------+
+-------------------+
The tone generator will respond to both note data received via MIDI and the data generated by the AN1x such as note data and control data.
ALL SOUNDS OFF clears all the sounds in the specific channel played by both the keyboard and the data via MIDI.
MIDI Data Table <1-1>
Parameter Base Address
Parameter Change
Address
Description
(H)
(M)
(L)
SYSTEM
00
00
00
System
USER PATTERN
01
00
00
User Pattern 1
(only Bulk Dump)
:
01
7F
00
User Pattern 128
(only Bulk Dump)
CURRENT VOICE
10
00
00
Current Voice Common Buffer
10
10
00
Current Voice Scene 1 Buffer
10
11
00
Current Voice Scene 2 Buffer
P11-19
97.7.11
1:36
PM
y
[
W
13