ROWENTA MINI SPACE CYCLONIC RO3349 - Manual (Page 13)

9
PLUGGING IN THE POWER CORD AND SWITCHING ON THE VACUUM CLEANER
• Unwind the power cord completely, plug in your vacuum cleaner - Fig.6 and press on the
On/Off button (2) - Fig.7.
• Set the suction power using the manual power switch on the power nozzle: open the regulator cover to
reduce the suction power manually, e.g.: on fragile surfaces… - Fig.8.
STORING AND CARRYING THE APPLIANCE
• After use, switch off your vacuum cleaner by pressing the On/Off switch (2) and unplug it - Fig.9.
Rewind the power cord by pressing the power cord rewind button (3) - Fig.10.
• In the vertical position, place the nozzle (19) in its storage compartment underneath the appliance (1b) -
Fig.11.
• In the horizontal position, place the nozzle (19) in its storage compartment at the back of the appliance
(1a)- Fig.12.
• Use the carrying power nozzle to carry your vacuum cleaner easily (5).
V. CLEANING AND MAINTENANCE
Important: Always switch off and unplug your vacuum cleaner before servicing or cleaning it.
Important: Whenever cleaning the dust container, make sure you’re standing over a dustbin.
REMOVE THE DUST CONTAINER (10)
• Remove the flexible hose (16) from the vacuum inlet (7) - Fig.2.
• Take out the dust container (10) from its compartment (6): press the dust container release clip (10a) -
Fig.13, then remove the container - Fig.14.
1. EMPTY THE DUST CONTAINER
Important: empty the dust container (10) each time you finish using the vacuum cleaner.
• Lift off the cover (10b).
• Press the push button for opening the cover (10c) – Fig.15, then remove the cover – Fig.16.
• Empty the container over a dustbin – Fig.17.
• Make sure that there is no more dust left in the container.
• Put the cover back on (10b) : place the sprockets in the notches – Fig.18, then close the cover – Fig.19.
• Put the container back in its compartment (6) – Fig.20.
2. CLEAN THE BLACK FOAM FILTER (11a)
Important!
To get the most out of your vacuum cleaner, make sure you wash the foam (11a) after each time you
empty the dust container (10).
• Pull simultaneously on the opening clips for the (H)EPA filter cassette (10d) – Fig.21.
• Separate the black foam filter (11a) from the (H)EPA filter (11b) – Fig.22.
• Wash the black foam filter (11a) in tap water, wring it like a sponge then dry it for 12 hours – Fig.23.
• Once it is completely dry, assemble the (H)EPA filter cassette (11) : the black foam filter (11a) and
(H)EPA filter (11b) under the dust container (10) – Fig.24, put the cover back on – Fig.19, then put the dust
container back in its compartment (6) – Fig.20.
Important!
The black foam filter (11a) must be put back in the appliance when it is completely dry.
You can still use your vacuum cleaner whilst the black foam filter is drying (11a) by using the replace-
ment black foam filter(11a (b)).
3. CLEANING THE DUST CONTAINER (10) AND THE AIR/ DUST SEPARATOR (12)
Important: clean the dust container (10) and the dust separator (12) every month.
• Take the lid off (10b) using the push button for opening the cover (10c) – Fig.15-16.
• Empty the dust container over a dustbin – Fig.17.
• Unclip the (H)EPA filter cassette (11), by pulling simultaneously on the opening clips (10d) located at the
EN
RO_ASPIRATEUR_MINI-SPACE-CYCLONIC_902827_902827 16/06/11 11:08 Page9