Spicer Drive Axles Illustrated Parts List Dana Spicer Service Carrier List - Manual (Page 49)

48
New Service Carriers Tandem Drive Axles
Tandem Drive Axle - Two Speed Carriers
RT341 - Two Speed Carrier and No Spin Carrier
16.00" Spiral Bevel Gearing (3.36-3.70 Ratio)
16.50" Spiral Bevel Gearing (3.90-7.17 Ratio)
Side Gear # 110525
No Spin # 110829
These new carrier units will directly replace tandem axle model
RT341 and single axle models 19055T and 19060T with no
modifications.
Side Gear New
Ratio Spline Carrier No Spin
3.70/5.05 39 Inv 675275
3.90/5.32 39 Inv 675458
4.11/5.61 39 Inv 675459
4.33/5.91 39 Inv 675299
4.56/6.21 39 Inv 675374
4.88/6.65 39 Inv 674920
5.57/7.60 39 Inv 674905
6.14/8.55 39 Inv 674930
6.57/8.96 39 Inv 675234
7.17/9.77 39 Inv 674787 219374
DT402(P) - Two Speed Carrier
16.00" Spiral Bevel Gearing (3.36-3.70 Ratio)
16.50" Spiral Bevel Gearing (3.90-7.17 Ratio)
Side Gear # 110527
These new carrier units will directly replace models DT381(P),
DT402(P), DT403(P) and DT451(P) built with 41 Involute spline
side gears. (See Note 1)
Side Gear Non-Pump New Carrier
Ratio Spline New Carrier w/Pump
3.70/5.05 41 Inv 674852 674777
3.90/5.31 41 Inv 674554 674600
4.11/5.61 41 Inv 674555 674601
4.33/5.91 41 Inv 674556 674602
4.56/6.21 41 Inv 674557 674603
5.29/7.21 41 Inv 674702 681387
5.57/7.60 41 Inv 674857 675517
6.57/8.96 41 Inv 676130 675394
RT402 - Two Speed Carrier and No Spin Carrier
16.00" Spiral Bevel Gearing (3.36-3.70 Ratio)
16.50" Spiral Bevel Gearing (3.90-7.17 Ratio)
Side Gear # 110527
No Spin # 110830
These new carrier units will directly replace models RT381,
RT402, RT403, RT451, 21060T, 22060T, 21065T(See Notes 1 & 3)
Also replaces 21065P & RP402. (See Note 2)
These units can be used as a replacement for model 22220 when
a new yoke and slinger is used. See yoke section for proper
selection.
Side Gear New With
Ratio Spline Carrier No Spin
3.70/5.05 41 Inv 674698
3.90/5.32 41 Inv 674558
4.11/5.61 41 Inv 674559 219173
4.33/5.91 41 Inv 674560
4.56/6.21 41 Inv 674561 219174
4.88/6.65 41 Inv 674565
5.57/7.60 41 Inv 674700
6.14/8.38 41 Inv 674701
6.57/8.96 41 Inv 675460
7.17/9.77 41 Inv 675461
Note 1: In Nov. 1995, the models DT/RT451(P) and DP/
RP451(P) were produced in both 33 and 41 Involute side gear
configurations. Before ordering a service carrier verify correct
spline count.
Note 2: Original carriers no longer available. Replaced by RT402
carrier and 122680 seasonal engagement kit. Refer to section on
seasonal engagement kits.
Note 3: If replacing a 21065T or 22065T w/RT402 service carrier,
be sure to use correct replacement carrier to HSG FASTENERS
(see kits page xx).
RT402/21060T = English threaded fasteners
21065/22065T = Metric threaded fasteners