Milton CAT 966K - Manual (Page 18)

966K Wheel Loader Specifi cations
Operating Specifications
Bucket Type
Edge Type
Bolt-On
Edges
4.20
5.49
3.80
4.97
3220
10'6"
2991
9'9"
1388
4'6"
2838
9'3"
124
4.9"
8691
28'7"
5902
19'5"
14 778
48'6"
16 635
36,664
17 855
39,353
14 636
32,259
15 828
34,886
173
38,984
24 189
53,311
Capacity – Rated (§) m 3
yd 3
Capacity – Struck (§) m 3
yd 3
Width (§) mm
ft/in
Dump Clearance at Maximum Lift and 45° Discharge (§) mm
ft/in
Reach at Maximum Lift and 45° Discharge (§) mm
ft/in
Reach at Level Lift Arm and Bucket Level (§) mm
ft/in
Digging Depth (§) mm
in
Overall Length mm
ft/in
Overall Height with Bucket at Maximum Lift mm
ft/in
Loader Clearance Circle with Bucket at Carry Position (§) mm
ft/in
Static Tipping Load, Straight (ISO)* kg
lb
Static Tipping Load, Straight (Rigid Tire)* kg
lb
Static Tipping Load, Articulated (ISO)* kg
lb
Static Tipping Load, Articulated (Rigid Tire)* kg
lb
Breakout Force** (§) kN
lb
Operating Weight* kg
lb
General Purpose – Pin On
Teeth and Bolt-On Teeth and
Segments Teeth Edges Segments Teeth
4.20 4.00 4.60 4.60 4.40
5.49 5.23 6.02 6.02 5.75
3.80 3.60 4.05 4.05 3.90
4.97 4.71 5.30 5.30 5.10
3271 3271 3220 3271 3271
10'8" 10'8" 10'6" 10'8" 10'8"
2837 2837 2977 2823 2823
9'3" 9'3" 9'9" 9'3" 9'3"
1525 1525 1400 1537 1537
5'0" 5'0" 4'7" 5'0" 5'0"
3043 3043 2857 3062 3062
9'11" 9'11" 9'4" 10'0" 10'0"
124 94 124 124 94
4.9" 3.7" 4.9" 4.9" 3.7"
8916 8916 8710 8935 8935
29'4" 29'4" 28'7" 29'4" 29'4"
5902 5902 5874 5874 5874
19'5" 19'5" 19'4" 19'4" 19'4"
14 951 14 951 14 787 14 961 14 961
49'1" 49'1" 48'7" 49'1" 49'1"
16 453 16 693 16 631 16 447 16 792
36,262 36,792 36,655 36,249 37,010
17 669 17 913 17 875 17 687 18 047
38,943 39,480 39,397 38,983 39,777
14 452 14 677 14 622 14 436 14 771
31,853 32,349 32,227 31,817 32,556
15 642 15 869 15 837 15 649 15 997
34,476 34,977 34,906 34,492 35,257
171 184 170 168 180
38,618 41,343 38,277 37,912 40,561
24 326 24 163 24 229 24 366 24 203
53,615 53,255 53,399 53,703 53,343
* Static tipping loads and operating weights shown are based on a machine configuration with Michelin 26.5R25 XHA2 L3 Radial tires, full
fluids, operator, standard counterweight, cold start, roading fenders, Product Link, open differential axles (front/rear), power train guard,
secondary steering, and sound suppression.
** Measured 102 mm (4") behind tip of cutting edge with bucket hinge pin as pivot point in accordance with SAE J732C.
*** Rock bucket specifications are given on Michelin 26.5R25 XLDD2 L5 Radial tires.
(§) Specifications and ratings conform to all applicable standards recommended by the Society of Automotive Engineers, including SAE
Standard J732C governing loader ratings.
(ISO) Full compliance to ISO 14397­1 (2007) Sections 1 thru 6, which requires 2% verification between calculations and testing.
(Rigid Tire) Compliance to ISO 14397­1 (2007) Sections 1 thru 5.
18