Velleman VDPL1803MHRGB User Manual
Page 7
VDPL1803MHRGB
V. 01 – 26/10/2012
7
©Velleman nv
Display Description
Sound-activation
possible
Pan/tilt movement
possible
ManualDimmer Custom colour. See Manual Mode for more
information.
no
no movement, but
stationary pan/tilt
position is adjustable
Note: At power-on, the device automatically enters DMX mode (the display shows <LED Addr:xxx>).
To set the device to stand-alone mode:
1. Connect nothing to the DMX input [4] of the device.
2. Press <SET/ESC> until <SET Menu> is displayed and press <ENTER>.
3. Use <UP> and <DOWN> to select <Master/Alone> and press <ENTER>.
4. Use <UP> and <DOWN> to select <Alone Mode> and press <ENTER>.
The indicator “Alone” will appear at the bottom right of the display when you choose the built-in program.
5. Use <UP> and <DOWN> to select <Auto/Sound> and press <ENTER>.
6. Use <UP> and <DOWN> to select the desired mode:
o
<Auto Mode> for normal mode. The indicator “Auto” will appear at the bottom left of the display when
you choose the built-in program.
o
<Sound Mode> for sound-activated mode. The indicator “Sound” will appear at the bottom left of the
display when you choose the built-in program.
7. Press <ENTER> to confirm.
8. Press <SET/ESC> until <LED xxx> is displayed.
9. Use <UP> and <DOWN> to select the desired program. The selected program starts automatically.
10. To activate pan/tilt movement with the program, press <ENTER>. The display shows <Motor Run>.
11. Press <ENTER>.
12. Use <UP> and <DOWN> to select <ON> and press <ENTER>.
The motor now starts moving the head.
Note: At power-on, the motor is deactivated for the programs.
Setting the Microphone Sensitivity
For sound-activated mode, you can adjust the sensitivity of the internal microphone. The default sensitivity
is 20%. To change the sensitivity of the internal microphone, proceed as follows:
1. Press <SET/ESC> until <SET Menu> is displayed and press <ENTER>.
2. Use <UP> and <DOWN> to select <MIC Sense> and press <ENTER>.
3. Use <UP> and <DOWN> to change the sensitivity (00 ~ 99%) and press <ENTER>.
Manual Mode
The manual mode (display: <LED Manual Dimmer>) allows you to define a custom colour by adjusting the
brightness of each LED colour (red, green, blue, white), and a precise head position by defining the exact pan
and tilt positions. You can also add a strobe effect, or even switch all the LEDs off.
1. Press <SET/ESC> until <LED xxx> is displayed.
2. Use <UP> and <DOWN> to select <LED Manual Dimmer> and press <ENTER>.
3. Use <UP> and <DOWN> to select the desired setting.
Refer to the table below for descriptions of the different settings:
Menu item
Setting
Description
Light switch
ON/OFF
Select ON to switch the LEDs on. Select OFF to switch the LEDS off.
Light red
0 ~ 255
Set the brightness of the red LEDs.
Light green
0 ~ 255
Set the brightness of the green LEDs.
Light blue
0 ~ 255
Set the brightness of the blue LEDs.
Light white
0 ~ 255
Set the brightness of the white LEDs.
Light strobe
0 ~ 255
Select one of various strobe effects.
Scan pan
0 ~ 255
Set the pan position.
Scan tilt
0 ~ 255
Set the tilt position.
Scan pan fine
0 ~ 255
Fine-tune the pan position.
Scan tilt fine
0 ~ 255
Fine-tune the tilt position.
Light calibrate Password protected. Do not change these settings.