Velleman LX500 - Manual (Page 5)

V.
DM
•
•
•
7.
Th
ma
If y
flu
If t
de
Th
•
•
7.
Ac
Bu
<F
<U
<D
<T
<V
<M
7.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10
02 – 18/12/2
MX-512 Con
When appl
side to the
linking cab
Maximum
of devices
A DMX term
an electric
signal by e
and 3, whi
. Oper
The
pum
the
e device doe
ains.
you experien
id level, the
the device w
vice to your
e LX500 can
stand-alon
with a DMX
1 Contr
cess the con
utton
FUNCTION>
UP>
DOWN>
TIMER>
VOLUME>
MANUAL>
2 Prepa
Make sure
Open the f
Remove th
Fill the res
not spill liq
Screw the
place and
Put the res
To direct t
the desired
Connect on
outlet.
The device
Wait until t
instruction
0. This device
off the pow
the device
012
nnection
icable, conn
e male XLR in
ble should be
recommend
on a serial d
minator is re
ally noisy en
electrical noi
ch is then p
ration
device doe
mp will cont
device can
es not have
nce low outp
circuit brea
will not funct
dealer. Rem
n be used in
ne mode
X512 contro
ol Panel N
ntrol panel fu
Function
accesses t
scrolls thr
scrolls thr
starts the
starts the
starts the
aration
the power c
flight case an
he cap [7] o
ervoir with t
quid onto the
cap firmly b
in good cond
servoir back
he haze up o
d direction.
ne end of th
e starts warm
the display s
ns.
e features an
wer to let the
cool down.
nect an XLR c
nput [3,10]
e a dual core
ed serial dat
data link is 3
ecommended
nvironment (
se. The DMX
lugged into
es not featu
tinue worki
suffer perm
an on/off sw
put, mechan
ker, and the
ion after 30
member to d
the followin
ller.
Navigation
unctions usin
the menu an
rough the me
rough the me
timer-contro
volume-con
manual mod
cable is not
nd pull out t
f the reservo
the appropri
e device.
back on the r
dition.
in the flight
or down, pu
e power cab
ming up. The
shows “READ
n automatic
e machine co
cable to the
of the LX50
e, screened c
ta link distan
32 devices.
d for installa
(e.g. discos)
X terminator
the XLR outp
ure an auto
ing. Always
manent dam
witch. It star
ical noise or
e power cord
seconds, dis
rain the rese
g modes:
n
ng the contr
nd scrolls thr
enu options
enu options
olled mode
ntrolled mode
de
plugged into
the reservoir
oir.
ate haze flu
reservoir, m
t case. Make
ll out the ha
ble to the pow
e display sho
DY TO HAZE
heater clean
omplete the
LX500
5
female XLR
00. Multiple
cable with X
nce is 500 m
ations where
). The termin
r is simply an
put socket [
omatic stop
s monitor th
mage when
rts operating
r no output a
d. If all appe
scontinue op
ervoir before
ol buttons [8
rough the m
in ascending
in descendin
e
o the mains.
r [6].
id (order cod
aking sure t
sure the ho
ze outlet [1
wer input [9
ows “WARMI
”. Refer to S
ning function
cleaning pro
output of a
LX500s can
LR input and
meters (1640
e the DMX ca
nator preven
n XLR plug w
2,11] of the
function w
he reservoi
n running w
as soon as
at all, unplug
ars to be wo
peration to a
e transportin
8] located d
enu options
g order, or in
ng order, or
de VDLSLHT
hat the plas
ose from the
] (squeeze t
9] and plug t
ING UP”.
Stand-Alone
n. After use,
ocess. Then
controller (n
be linked th
d output con
0 ft). Maximu
able has to r
nts corruptio
with a 120 Ω
e last device
when runnin
ir fluid leve
without flui
you plug the
g the device
orking prope
avoid perman
ng the unit.
directly unde
ncreases a n
decreases a
T5). Do not o
tic hoses att
reservoir is
the sides tog
the other en
e Mode and
wait for 3 m
disconnect t
not incl.) and
rough serial
nnectors.
um recomme
un a long dis
n of the digi
Ω resistor bet
e in the chain
ng out of fl
el during op
d.
e power cord
immediately
rly, plug in t
nent damage
erneath the d
numeric valu
a numeric va
overfill the re
tached to the
not bent.
gether) and
nd into a suit
d DMX Mode
minutes befo
the power ca
©Velleman
d the other
linking. The
ended numb
stance or is
ital control
tween pins 2
n.
uid; the
peration as
d into the
y. Check the
the unit aga
e. Return th
display [5].
e
alue
eservoir. Do
e cap are in
re-insert it i
table mains
e for operati
ore switching
able and let
n nv
e
ber
in
2
e
in.
e
n
ng
g