Speedhut Edge Attitude Pillar, Pod, and Mount - Manual

www.Speedhut.com Need help? Contact us: Speedhut Inc. 165 North 1330 West B2 Orem, Utah 84057 or call 801-221-1460
Installation Instructions: Pillars and Pods with Edge Attitude Mount
Models #13008, #13009 are designed to fit 98-02 Dodge Ram (Velcro and rachet fasteners)
STEP ONE: Remove the stock A-pillar
STEP TWO: For models with the Infinity speaker, remove speaker from A-pillar. Cut or grind down the raised speaker hole on the stock A-pillar to allow
the mounting of the new A-pillar mount.
STEP THREE: Hold the A-pillar mount in position on the factory A-pillar. Slight trimming of the A-pillar mount may be required for a perfect fit in some
applications. Drill 3/16” holes through the 4 corners of both the mount and factory A-pillar.
STEP FOUR: Attach the two pieces of Velcro together. Peel back from one side and attach to the recessed area of the mount where the Attitude fits.
STEP FIVE: Install Attitude in pod, press firmly to engage adhesive to back of Display (don’t press on LCD).
STEP SIX: The mount has clearance for the Attitude wires to be run down the back and through the bottom. Secure wiring to the back of the new mount.
STEP SEVEN: Insert ratchet fasteners through holes to attach mount to factory A-pillar.
STEP EIGHT: Re-install mount/factory A-pillar assembly, making sure wires are not pinched.
Model #13005 is designed to fit 2003+ Dodge Ram (velcro and long bolt)
STEP ONE: Attach the two Velcro pieces together. Peel back strip from one side and attach to the recessed area of the mount where the Attitude fits.
STEP TWO: Install Attitude in pod, press firmly to engage adhesive to back of Display.
-Do not press on LCD
STEP THREE: Run wires between mount and the stock A-pillar. There is a visible channel molded in for the wire.
STEP FOUR: Remove the lower cap and screw from the stock A-pillar handle.
STEP FIVE: Place mount over the stock A-pillar.
STEP SIX: Use provided (longer) screw to secure mount and A-pillar.
STEP ONE: Attach the two Velcro pieces together. Peel back strip to expose adhesive from one side and attach to the recessed area of the mount where
the Attitude fits.
STEP TWO: Expose adhesive and install Attitude in mount. Press firmly to engage adhesive to back of Display (Do not press on LCD).
STEP THREE: Remove Handle from A-pillar (8mm bolts).
STEP FOUR: Run wires between mount and pillar (extra space has been provided for wires).
STEP FIVE: Place mount on pillar.
STEP SIX: Reinstall handle (The handle will catch the top edge of mount, holding it in place).
Model #13001 is designed to fit Ford SD 03-06 (velcro)
Model #13000 is designed to fit Ford SD 99-02 (velcro and ratchet fasteners)
Model #13012 and 13013 are designed Chevy 07+ (velcro and screw)
Installation Instructions: 03-06 Ford Super Duty
Installation Instructions: 98-02 Dodge Ram
Installation Instructions: 03+ Dodge Ram
STEP ONE: Attach the two Velcro pieces together. Peel back strip to expose adhesive from one side and attach to the recessed area of the mount
where the Attitude fits.
STEP TWO: Expose adhesive and install Attitude in mount. Press firmly to engage adhesive to back of Display (Do not press on LCD).
STEP THREE: Run wires between mount and pillar (extra space has been provided for wires).
STEP FOUR: Place mount on A-pillar in final position.
STEP FIVE: Along the top of the mount, drill a 5⁄32” hole through the mount and A-pillar.
STEP SIX: Press in Ratchet Fasteners.
STEP ONE: Remove stock pillar (screw is located under the cap at the top of the pillar).
STEP TWO: Attach the two pieces of Velcro, peel one side and attach to recessed pocket area of the Attitude mount.
STEP THREE: Install Attitude in pillar, press firmly to engage adhesive to back of display (do not press on LCD).
STEP FOUR: Use provided screw to hold pillar in place: (Don’y over tighten screw, Snug Only)
Your new A-pillar mount installs over the factory A-pillar. It is not a replacement.
Installation Instructions: 99-02 Ford Super Duty
Installation Instructions: 07+ Chevy/GMC