Table 1. power requirement for pcie connectors – Rainbow Electronics MAX5960 User Manual
Page 16
MAX5959/MAX5960
Quad PCI Express, Hot-Plug Controllers
16
______________________________________________________________________________________
At power-up, the MAX5959/MAX5960 keep all the
external MOSFETs off until all supplies rise above their
respective UVLO thresholds. These devices keep the
internal MOSFETs off only until the 3.3VAUXIN supply
rises above its UVLO threshold. Upon a turn-on com-
mand, the MAX5959/MAX5960 enhance the external
and internal MOSFETs slowly with a constant gate cur-
rent to limit the power-supply inrush current. The
MAX5959/MAX5960 actively limit the current of all out-
puts at all times and shut down the corresponding
channel if an overcurrent condition persists for longer
than a resistor-programmable overcurrent timeout (see
the
Fault Management
section). Thermal protection cir-
cuitry also shuts down all outputs if the die temperature
exceeds +150°C. After an overcurrent or overtempera-
ture fault condition, the MAX5959/MAX5960 latch off or
automatically restart depending on the version, after a
restart time delay.
The power requirement for PCIe connectors is defined
by the PCIe card specification and summarized in
Table 1.
Startup
The main supply outputs can become active only after
all the following events have occurred:
• V
3.3AUXIN
is above its UVLO threshold.
• V
12VIN
and V
3.3SA+
are both above their UVLO
threshold.
• ON_ is driven high.
•
PRES-DET_ is low for more than 4ms.
The auxiliary supply output is made available only after
the following events have occurred:
• V
3.3AUXIN
is above its UVLO threshold.
• AUXON_ is driven high.
•
PRES-DET_ is low for more than 4ms.
The
FON_ input overrides all other control signals and
turns on the respective slot when driven low, as long as
the UVLO thresholds have been reached. Table 2 sum-
marizes the logic conditions required for startup. The aux-
iliary supply input powers the internal control logic and
analog references of the MAX5959/MAX5960, so the main
supplies cannot be enabled, if V
3.3VAUXIN
is not present.
When an output is enabled, a programmable startup
timer (t
SU
) begins to count the startup time duration.
The value of t
SU
is set to 2x the fault timeout period
(t
FAULT
). R
TIM
externally connected from TIM to GND
sets the duration of t
FAULT
.
Table 1. Power Requirement for PCIe Connectors
POWER FAIL
X1 CONNECTOR
X4/8 CONNECTOR
X16 CONNECTOR
3.3V
Voltage Tolerance
±9% (max)
±9% (max)
±9% (max)
Supply Current
3.0A (max)
3.0A (max)
3.0A (max)
Capacitive Load
1000µF (max)
1000µF (max)
1000µF (max)
12V
Voltage Tolerance
±8% (max)
±8% (max)
±8% (max)
Supply Current
0.5A (max)
2.1A (max)
5.5A (max)
Capacitive Load
300µF (max)
1000µF (max)
2000µF (max)
3.3V AUXILIARY
Voltage Tolerance
±9% (max)
±9% (max)
±9% (max)
Supply Current, Wake Enabled
375mA (max)
375mA (max)
375mA (max)
Supply Current, Nonwake Enabled
20mA (max)
20mA (max)
20mA (max)
Capacitive Load
150µF (max)
150µF (max)
150µF (max)