Rainbow Electronics АТ89С2051 - Manual (Page 9)

AT89C2051
9
Notes: 1. Under steady state (non-transient) conditions, I
OL
must be externally limited as follows:
Maximum I
OL
per port pin: 20 mA
Maximum total I
OL
for all output pins: 80 mA
If I
OL
exceeds the test condition, V
OL
may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test conditions.
2. Minimum V
CC
for Power-down is 2V.
Absolute Maximum Ratings*
Operating Temperature ................................. -55°C to +125°C *NOTICE: Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin
with Respect to Ground .....................................-1.0V to +7.0V
Maximum Operating Voltage ............................................ 6.6V
DC Output Current...................................................... 25.0 mA
DC Characteristics
T
A
= -40°C to 85°C, V
CC
= 2.0V to 6.0V (unless otherwise noted)
Symbol Parameter Condition Min Max Units
V
IL
Input Low-voltage -0.5 0.2 V
CC
- 0.1 V
V
IH
Input High-voltage (Except XTAL1, RST) 0.2 V
CC
+ 0.9 V
CC
+ 0.5 V
V
IH1
Input High-voltage (XTAL1, RST) 0.7 V
CC
V
CC
+ 0.5 V
V
OL
Output Low-voltage (1)
(Ports 1, 3)
I
OL
= 20 mA, V
CC
= 5V
I
OL
= 10 mA, V
CC
= 2.7V
0.5 V
V
OH
Output High-voltage
(Ports 1, 3) I
OH
= -80 µA, V
CC
= 5V ± 10% 2.4 V
I
OH
= -30
µA
0.75 V
CC
V
I
OH
= -12 µA 0.9 V
CC
V
I
IL
Logical 0 Input Current
(Ports 1, 3) V
IN
= 0.45V -50 µA
I
TL
Logical 1 to 0 Transition Current
(Ports 1, 3) V
IN
= 2V, V
CC
= 5V ± 10% -750 µA
I
LI
Input Leakage Current
(Port P1.0, P1.1) 0 < V
IN
< V
CC
±10 µA
V
OS
Comparator Input Offset Voltage V
CC
= 5V 20 mV
V
CM
Comparator Input Common
Mode Voltage 0 V
CC
V
RRST Reset Pull-down Resistor 50 300 K Ω
C
IO
Pin Capacitance Test Freq. = 1 MHz, T
A
= 25°C 10 pF
I
CC
Power Supply Current Active Mode, 12 MHz, V
CC
= 6V/3V 15/5.5 mA
Idle Mode, 12 MHz, V
CC
= 6V/3V
P1.0 & P1.1 = 0V or V
CC
5/1 mA
Power-down Mode (2) V
CC
= 6V P1.0 & P1.1 = 0V or V
CC
100 µA
V
CC
= 3V P1.0 & P1.1 = 0V or V
CC
20
µA