Media-Tech SCANLINE COMBO - Manual (Page 2)

EN
Notes:
1. Before scanning,make sure the micro SD card has been inserted properly and
the scanner docking has been connected to external power.
2. Once fi xed on the docking, the scanner is unable to scan black or transparent
documents.
3. When the scanning document gets stuck or goes awry during the scanning
process, press Scan button to stop scanning, then take out the document and
restart scanning.
4. When scanning with docking, if no paper is detected into the scanning slot
within 4 or 5 seconds, just remove the scanning document, put it right in place
and scan again.
5. When scanning relatively thick documents such as credit card or ID, the nar-
row side,rather than the wide side, is suggested to be inserted into the slot to
guarantee normal scanning.
Note: How to calibrate the scanner
Perform calibration only when white balance needs adjustment.
1. Take the scanner out of the Docking Station.
2. With the dry cleaning cloth provided, clean the scanning lens located on the
bottom of the scanner.
3. Turn on the scanner by pressing the button. Place the scanner on the white
area of the White Balance Calibration paper provided.
4. Press and hold the Color/Mono button. While holding the Color/Mono button,
press the button and then release both buttons to enter into auto-calibration
mode. SD symbol will fl ash and then stop. SCAN/ERROR LED will turn red.
5. Do not move the scanner .Wait until the SCAN/ERROR LED turns green.
6. When the SCAN/ERROR LED is green, start scanning the white paper by sliding
the scanner across the paper until the SCAN/ERROR LED light turns off . (Slide
the scanner backwards if necessary).
7. Press and hold the button to power off the scanner. Calibration is complete.
8. Replace the scanner onto the Docking Station..
Charging
1. The scanner will keep charging when it is in connection with a computer via USB cable.
2. The scanner can also be charged via an adapter.
3. The scanner will enter into charge mode if no extra scanning action is detected
within 1 minute subsequent to each scanning.
6. When the fi xed button is oriented on the “Release” side, do not touch the re-
lease perch inside the docking, since a big sound may produce from the press-
ing and it may hurt your fi nger.
LED light indications
Specifi cations
Troubleshooting
LED indication Function Description
“Green” SCAN/ERROR LED ON Scan in progress.
“Green” SCAN/ERROR LED OFF Stand by/Scan is complete.
“RED” SCAN/ERROR LED ON May cause scanning error. Restart and scan again.
“RED” SCAN/ERROR LED OFF No error in scanning speed. Continue scanning process.
“RED” CHARGE LED keeps ON Battery is charging
“RED” CHARGE LED OFF Charge is over
“RED” CHARGE LED fl ashes Low power warning
Connect to computer
You may also connect your scanner to your computer and view pictures on the
computer monitor.
Without docking
Turn on your scanner by pressing the
button, connect your scanner to your
computer to enter into USB mode.”USB” symbol will display on status LCD. Click
“Open folder to view fi les” to view, import, copy, move or delete scanned fi les.
Functions and technical specifi cation of device are subject to change without prior notice.
For technical support please visit www.media-tech.eu
Image sensor A4 color Contact Image Sensor
Resolution High resolution: 1200dpi (w/ docking)
High resolution: 900dpi (w/o docking)
Middle resolution: 600x600 dpi
Low resolution: 300x300 dpi
Minimum scanning speed
for Letter size document Color High resolution 12 Seconds (w/o docking)
12 Seconds(w/ docking)
Mono High resolution 10 Seconds (w/o docking)
12 Seconds(w/ docking)
Color Medium resolution 8 Seconds (w/o docking)
10 Seconds(w/ docking)
Mono Medium resolution 6 Seconds (w/o docking)
10 Seconds(w/ docking)
Color Low resolution 3 Seconds (w/o docking)
8 Seconds(w/ docking)
Mono Low resolution 2 Seconds (w/o docking)
8 Seconds(w/ docking)
Capacity (Based on 1GB microSD card.
Scan Letter size fi le, the quantity of
scans varies depending on the content
complexity) Color High resolution 240 Scans (Min.) (w/o docking)
150 Scans (Min.) (w/ docking)
Mono High resolution 250 Scans (Min.) (w/o docking)
150 Scans (Min.) (w/ docking)
Color Medium resolution 550 Scans (Min.)
Mono Medium resolution 600 Scans (Min.)
Color Low resolution 1580 Scans (Min.)
Mono Low resolution 1600 Scans (Min.)
Scan width 216mm
Scan length 300 dpi: 330cm, 600 dpi: 228cm, 900 dpi: 177cm, 1200 dpi: 127cm
File format JPEG/PDF
LCD Scanning status display
Auto Power Off 3 Minutes
USB Port USB 2.0 high speed
External memory Micro SD Card
Standard Battery 700mAH Lithium-Polymer
Problem Cause Solution
Cannot turn on the scanner Low battery power Recharge the battery
Pictures cannot be saved
when you are scanning them 1. The micro SD card has not been installed
2. Memory is full
3. The micro SD card has not been formatted
properly 1. Install a micro SD card
2. Download the pictures from the scanner
to the computer to create storage space
3. Please refer to section: “Inserting a micro
SD memory card”
Computer does not recognize
your scanner when connected
(You cannot fi nd removable disk) Connection failure Make sure all cable connections are secured.
Restart the computer if necessary
Blurry images 1. The lens of scanner is dirty.
2. Contact Image Sensor aged. 1. Clean the lens with soft dry cloth.
2. The Scanner should be re-done
calibration
Black Images/Black or
white vertical lines 1. Scanner senor protective glass is dirty.
2. Calibration data is off -set. 1. Clean the sensor’s protective glass with
clean and soft dry cloth.
2. Recalibrate scanner. Refer to the note
below.
Zebra stripes occur on the top
or bottom of scanned document Scanning document goes awry during
scanning process Put scanning docunment right in place and
scan again.
SCAN/ERROR LED is on
when scanning a document Scanning speed is too fast Press the Power/Scan button to reset and
scan again the document
SCAN/ERROR LED is on
after powered on The calibration data is destroyed Recalibrate the scanner. Refer to the
note below
Black Image Contact Image Sensor aged. Recalibrate the scanner. Refer to the
note below.
Computer system minimum requirement
¯ Windows 7 / Vista / XP and Mac OS 10.4 or above (direct plug-in, driver instal-
lation not required)
¯ Pentium III or above ¯ RAM: At least 256MB ¯ USB port
With docking:
Turn on your scanner by pressing the
button, connect your scanner to your
computer. Press the button once to enter into USB mode. Your computer will
recognize the scanner as a “Removable Disk”, ”USB” symbol will display on sta-
tus LCD. Click “Open folder to view fi les” to view, import, copy, move or delete
scanned fi les. Press the
button again to switch to scanning mode.
NOTE: If the Removable Device Window did not launch automatically, go to your
“My Computer” and fi nd the device under Removable Storage.