Extron Electronics MLS 608 D Series Setup Guide - Manual

1
MLS 608 D Series • Setup Guide
Rear Panel Features — MLS 608 D and MTP HDMI U R
NOTE: The MLS 608 D SA, as shown below, is representative of the MLS 608 D Series. It has the maximum number and type of
connectors and features of the three models. The MLS 608 D model lacks the power amplifier output.
The Extron MLS 608 D Series are eight input, multi-format AV switchers with ProDSP ™ audio
and are able to integrate analog and digital sources. There are three models:
• MLS 608 D (with variable preamp output - no amplifier)
• MLS 608 D MA (with 40 watt 70 volt mono power amplifier)
• MLS 608 D SA (with 2 x 20 watt stereo power amplifier)
This guide allows you to easily and quickly setup and configure your MLS 608 D using step by step instructions. It covers performing
basic operations using the front panel controls and selected Simple Instruction Set (SIS
™ ) commands.
It also gives connection information for the MTP HDMI U R twisted pair receiver, which is supplied with the MLS 608 D Series unit.
See rear cover for a diagram of a typical MLS 608 D application, showing the MLS 608 D SA model.
NOTE: For full installation, configuration, and operation details for all MLS 608 D models, see the MLS 608 D Series User Guide,
and for complete details on the MTP HDMI U R, see the MTP HDMI U R User Guide, both available at
www.extron.com .
1
BUFFERED OUTPUT
MTP
+
AUDIO
+12 V OUT
PWR OUT= 12W
2 3
6
L R 1 L R 2 L R 3
L R 5 L R 7 L R 8 1 2 1 2 MIC/LINE + 48V
1
2
L R L R Tx
+12V
Rx 8
4 (MTP)
CONFIGURABLE ANALOG INPUTS AUDIO INPUTS
AUDIO OUTPUTS
RS-232
HOST
PWR OUT = 7.2 W
DIGITAL OUTPUT
VIDEO + RS-232
ANALOG OUTPUT
DIGITAL INPUTS
5
7 L R 6
Tx N/ A N/ A Rx
RS-232 INSERT
MLS 608 D SA
100-240V 50/60 Hz
1.2A MAX
1 2
4/8 OHM - 20W x 2
1 4 7 8 5 13 12 11 9
14 MLS 608 D SA
2
3
10
6
 Power input  MTP input  RS-232 port (analog side), not used in MLS 608 D system
 Digital signal inputs (1 and 2)  RGBHV, RGBS output*  Composite video output*
 Digital (HDMI) output  S-video output*  Component video (R-Y, Y, B-Y) output*
 RS-232 pass-through connector  Mono audio output * = Analog outputs
DIGITAL OUTPUT DIGITAL INPUT
POWER
12V
0.8A MAX
1 2
HDMI
RS-232
PASS THRU
Tx Rx
RGB
VID
Y/C
B-Y Y R-Y
ANALOG OUTPUTS
RS-232
Tx Rx SPARE
MTP INPUT
1
MONO AUDIO
2
MTP/HDMI U R
A B C F D A G H E
K I J
Pin T568A Wire Color T568B Wire Color
1 White-green White-orange
2 Green Orange
3 White-orange White-green
4 Blue Blue
5 White-blue White-blue
6 Orange Green
7 White-brown White-brown
8 Brown Brown
Power, Analog, and Digital Connections Audio and RS-232 Connections
a AC power connector i Audio inputs: 5-pole captive screw connectors (inputs 1-3, 5-8)
b RGB, component/S-video/composite inputs: 15-pin HD
connectors (inputs 1-3, see rear page for pinout details)
j Mic/line level audio inputs (1-2): 3-pole captive screw connectors
and phantom power LEDs
c Buffered output: 15-pin HD connector (tied only to input 1) k Line level audio output: 5-pole captive screw connectors
(audio outputs 1-2)
d Universal MTP RJ-45 connector (input 4, see rear page for
pinout details)
l Power amplifier output connector (MA and SA units only)
e 12 V output MTP/HDMI U R power source: 2-pole captive
screw connector
m RS-232 control/configuration port and +12 V power output
(for optional MLC power source): 5-pole captive screw connector
f Analog video and audio MTP output: RJ-45 connector n RS-232 insertion pass-through port: 5-pole captive screw connector
g Digital inputs: HDMI connectors (inputs 5-8)
h
Digital video and RS-232 outputs: RJ-45 connectors