Extron Electronics IPL 250 Reference Manual - Manual (Page 73)

4-17 IPL 250 • SIS Programming and Control
Command/r
esponse table for SIS commands (continued)
Command
ASCII (T
elnet)
(host to IPL)
URL Encoded (W
eb)
(host to IPL)
Response (IPL to host)
Additional description
Set user passwor
d 14, 24
E
X3#
CU
}
W
X3#
CU
|
Ipu•
X4!
]
Set the user passwor
d (
X3#
is 4 to 12
alphanumeric characters). The passwor
d is
case sensitive. Special characters (spaces, symbols) ar
e not allowed.
X4!
=
Passwor
d
to display on scr
een.
N
A
user password cannot be assigned if an administrator password does not exist. Also, if the administrator password is clear
ed, the user password is also clear
ed.
Clear user passwor
d 24
E
•CU
}
W%20CU
|
Ipu•
]
This clears the user passwor
d only
.
Read user passwor
d
E
CU
}
WCU
|
X4!
]
Remapping port designations
For security r
easons the network administrator may wish to assign new/dif
fer
ent port numbers to the contr
oller
’s T
elnet, W
eb br
owser
, and dir
ect access ports or to disable
one or mor
e ports. T
ypically T
elnet uses port 23, W
eb access is via port 80 (HTTP), and dir
ect access is via port 2001.
C
Do
not
set two or mor
e ports to the same port number
. Setting two ports to the same number could cause networking conflicts and will also r
esult in an E13 (invalid
parameter) err
or
.
N
If you r
emap a port, you must set the port number to 1024 or higher
, unless you r
eset the port to the default number or disable the port by setting it to 0.
Set the T
elnet port map
24
E
port#
MT
}
W
port#
MT
|
Pmt
port#
]
Select a number (
port#
) for the port that will
not conflict with any other ports.
Reset the T
elnet port map
24
E
23MT
}
W23MT
|
Pmt 00023
]
This r
esets the T
elnet port to port 23.
Disable the T
elnet port map
24
E
0MT
}
W0MT
|
Pmt 00000
]
Setting the port number to 0 disables the port.
Read the T
elnet port map
E
MT
}
WMT
|
port#
]
Set the W
eb (HTTP) port map
24
E
port#
MH
}
W
port#
MH
|
Pmh
port#
]
Reset the W
eb (HTTP) port map
24
E
80MH
}
W80MH
|
Pmh 00080
]
This r
esets the W
eb port to port 80.
Disable the W
eb (HTTP) port
24
E
0MH
}
W0MH
|
Pmh 00000
]
Read the W
eb (HTTP) port map
E
MH
}
WMH
|
port#
]
Set the Dir
ect
Access port map
24
E
port#
MD
}
W
port#
MD
|
Pmd
port#
]
Reset the Dir
ect
Access port
map
24
E
2001MD
}
W2001MD
|
Pmd 02001
]
This r
esets the dir
ect access port to port
2001.
Disable the Dir
ect
Access port
24
E
0MD
}
W0MD
|
Pmd 00000
]
Read the Dir
ect
Access port map
E
MD
}
WMD
|
port#
]