E8361a, Test port input, Dynamic accuracy (specification) – Atec Agilent-E8361A User Manual
Page 43: Continued
E8361A
Test port input
continued
Dynamic accuracy (specification)
1
Applies to input ports 1 and 2, accuracy of the test
port input power reading relative to the reference
input power level. Also applies to the following
conditions:
• IF bandwidth = 10 Hz
Note: If the power is set above maximum specified
leveled power, the test port output signal may show
non-linear effects that are dependent on the DUT.
Magnitude
0.01
0.1
1
10
-10
-110
-100
-90
-80
-70
-60
-50
-0
-0
-0
-10
0
10
Testport power (dBm)
E861A
-10 dBm (0.500-5 GHz)
-0 dBm (0.500-5 GHz)
-0 dBm (0.500-5 GHz)
-0 dBm (0.500-5 GHz)
Ac
cu
ra
cy
(d
B)
Phase
0.1
1
10
100
-10
-110
-100
-90
-80
-70
-60
-50
-0
-0
-0
-10
0
10
Testport power (dBm)
E861A
-10 dBm (0.500-5 GHz)
-0 dBm (0.500-5 GHz)
-0 dBm (0.500-5 GHz)
-0 dBm (0.500-5 GHz)
Ac
cu
ra
cy
(d
eg
re
es
)
Magnitude
0.01
0.1
1
10
-10
-110
-100
-90
-80
-70
-60
-50
-0
-0
-0
-10
0
10
Testport power (dBm)
E861A typical
-10 dBm at 0.05 GHz
-0 dBm at 0.05 GHz
-0 dBm at 0.05 GHz
-0 dBm at 0.05 GHz
Ac
cu
ra
cy
(d
B)
Phase
0.1
1
10
100
-10
-110
-100
-90
-80
-70
-60
-50
-0
-0
-0
-10
0
10
Testport power (dBm)
E861A typical
-10 dBm at 0.05 GHz
-0 dBm at 0.05 GHz
-0 dBm at 0.05 GHz
-0 dBm at 0.05 GHz
Ac
cu
ra
cy
(d
eg
re
es
)
Magnitude
0.01
0.1
1
10
-10
-110
-100
-90
-80
-70
-60
-50
-0
-0
-0
-10
0
10
Testport power (dBm)
E861A
-10 dBm (5-0 GHz)
-0 dBm (5-0 GHz)
-0 dBm (5-0 GHz)
-0 dBm (5-0 GHz)
Ac
cu
ra
cy
(d
B)
Phase
0.1
1
10
100
-10
-110
-100
-90
-80
-70
-60
-50
-0
-0
-0
-10
0
10
Testport power (dBm)
E861A
-10 dBm (5-0 GHz)
-0 dBm (5-0 GHz)
-0 dBm (5-0 GHz)
-0 dBm (5-0 GHz)
Ac
cu
ra
cy
(d
eg
re
es
)
1. Dynamic accuracy is verified with the following measurements: compression over
frequency, IF linearity at a single frequency of 1.195 GHz and and a reference level
of -0 dBm for an input power range of 0 to -10 dBm.