Atec Agilent-8566B - Manual (Page 12)

Fig. 6. Specified average displayed noise level,
2.0 to 22
preselected tuning range
Marker
(frequency and amplitude are read out continuously)
Marker Type Frequency Accuracy
Normal same as center frequency accuracy
Delta same as frequency span accuracy
Amplitude Accuracy
Normal same as reference level accuracy +
scale fidelity between the reference
level and marker position
Delta same as frequency response
uncertainty and scale fidelity
between two markers
Sweep Time Accuracy (1 to 1500s full sweep)
200 second sweep time, 10%
200 second sweep time, 30%
Inputs
RF Input 100 Hz to 22 precision type-N
female connector, dc-coupled
Maximum Input Level
ac Continuous power:
from 50 ohm source
Mixer protected by diode limiter,
100 Hz-2.5
Pulse power: 100 W, 1
pulse width with
50 input attenuation
( I 0 peak power to input mixer)
100 damage level
Input Attenuator0 to 70 in steps
SWR (typical) Tune Frequency
Input 100Hzto 2 to 5.8 to
Attenuation 2.5 5.8 22
1.2 1.5 1.9
0 dB* 2.3 3.0 3.0
‘when tuned to within MHz of signal
IF Input
Maximum Input Level
ac +10 continuous power from
50 ohm source
dc 20 V with rise time of 1
External Sweep Trigger Input (rear panel) Must be
2.4 V (5 V max), 1 kohm nominal input impedance.
External Frequency Reference Input Must equal
5 MHz 25 Hz or MHz Hz, 0 to
50 ohm nominal input impedance. Analyzer performance
will be degraded unless frequency reference phase noise
and spurious signals are
40 single sideband
(1 Hz) referred to 10 MHz at a 100 Hz to 10 offset.
Quasi-Peak (rear panel; nominal values)
Video Input 0 to 2 V, 139 ohm input impedance
21.4 MHz IF Input Nominally -11 with 10
input attenuation, 50 ohm input impedance
Calibrator (front panel)
100 MHz (frequency reference error x 100 MHz)
-10 0.3 50 ohm impedance, nominal
1st LO (front panel)
2.3 to 6.1
50 ohm impedance, nominal
Sweep and Tune Output (rear panel)
-1 of tuned frequency (2% + 10
kohm impedance, nominal
Display Outputs (typical parameters)
X, Y, and Z outputs for auxiliary CRT displays.
1 V for full deflection
Z 0 to 1 V intensity modulation, -1 V blank
BLANK TTL level 2.4 V for blanking
Compatible with most oscilloscopes.
Recorder Outputs (typical parameters)
Outputs to drive all current HP X-Y recorders using positive
or TTL pen uplift.
Horizontal Sweep Output (X-axis)
A voltage proportional to the horizontal sweep of the
frequency sweep generator. 0 V for left edge,
0
V for right edge; 1.7 kohm impedance, nominal.
Video Output (Y-axis)
Detected video output (before A-D conversion)
proportional to vertical deflection of the CRT trace
100
from 0 to 1 V; 475 ohm impedance,
nominal.
Output (Z-axis)
During sweep, pen down 0 V from ohm source
During retrace, pen up V from kohm source
21.4 MHz Output (rear panel, typical)
21.4 MHz; 50 ohm impedance, nominal: -20
for a signal
at reference level. In log scales, the IF output logarithmically
related to RF input signal; in linear, the output is linearly
related.
Frequency Reference (rear panel, typical)
10.000 MHz, 0 50 ohm output impedance
10 MHz Output (rear panel, typical)
5 to ohm output impedance
Video Output 0 to 2 V, 10 ohm output impedance
Cathode Ray Tube Post deflection accelerator,
aluminized phosphor, electrostatic focus and
deflection.
Viewing Area
Approximately 9.6 cm vertically
by 11.9 cm horizontally (3.8 in x 4.7 in)