Baldwin Soho Sectional Handleset - Manual (Page 2)

©2010 Baldwin Hardware Corporation, Lake Forest, CA 92610 PK.9009 (2/10)
fold line fold line
fold line
fold line fold line
fold line
INTERIOR TRIM
WARRANTY INFORMATION
LIMITED LIFETIME MECHANICAL WARRANTY
Baldwin warrants that each Baldwin product shall be free from mechanical
defects at the time of delivery and for the lifetime of the product or as long
as you own your home.
LIMITED LIFETIME FINISH™ WARRANTY
The Baldwin Lifetime Finish™ uses advanced finishing technology (physical
vapor deposition) to create a finish highly resistant to the effects of weather and
normal wear and tear. The Limited Lifetime Finish Warranty on Lifetime Finish™
products covers the original purchaser for as long as you own your home.
LIMITED FINISH WARRANTY
The finish on Baldwin products (excluding Lifetime Finish and living finish
products) is protected by a durable topcoat designed to maintain the beauty
and quality of the Baldwin product. The Baldwin Limited Finish Warranty
covers the original purchaser for five years from date of purchase for interior
use and one year for exterior use.
LIVING FINISHES
Due to the nature of Baldwin living finish products, they will wear over time
and may already have begun the process before reaching your home. No
finish warranty is offered on living finish products, which are designed to age
and improve over time. Living finishes include raw brass, oil rubbed bronze,
stainless steel, and other non-lacquered or non-PVD finishes.
REFER TO WWW.BALDWINHARDWARE.COM FOR A COMPLETE
WARRANTY STATEMENT.
TROUBLESHOOTING GUIDE
If parts are missing do not return product. Please call Baldwin’s
Consumer Help Line at 1-800-566-1986 and we will quickly send the
parts to you.
SCREWS ARE ALL TIGHT BUT THE HARDWARE IS NOT FIRMLY
ATTACHED TO THE DOOR.
Check door thickness. Door must be 1 - 3⁄4” thick. Hardware will not
install on doors less than 1 - 3⁄4” thick.
KNOB OR LEVER KEEPS COMING OFF THE SPINDLE.
Ensure that set screw on knob or lever is installed in V groove on
spindle and securely tightened with Allen wrench provided. Refer to
handleset installation step 5.
DOOR IS DIFFICULT TO LATCH OR WILL NOT STAY CLOSED.
Strikeplate is not aligning with latchbolt. Remove, plug holes with wooden
dowels and glue. Adjust and re-install. Condition can also be caused by
weather stripping being installed after hardware is installed. Re-install strike
as described at left. Refer to strikeplate installation step 1.
1. Place spindle (F) into latch (A) with the V-groove pointed to the hinge side of door (see view). Slide spacer (G) over spindle (F).
2. Install adaptor (H) over spindle (F) and secure with adaptor screws (J).
3. Test operation of handleset. If latch does not operate smoothly, loosen screws (E) and (J) and gently lift up the exterior subassembly
while retightening (J) screws. Test operation again.
4. Snap rose (K) onto adaptor. See alternate rose configuration when applicable.
5. Slide lever (L) onto spindle and secure with set screw (M) using supplied allen wrench (Q).
6. Tighten (E) screw and snap screw cover (P) over retainer (D).
7. Refer to PK.9008 for Keyless Entry Deadbolt installation.
F
A
G
H
J
K
L
N
P
Q
DOOR HINGE ALTERNATE ROSE CONFIGURATION
1. Place the rose (K) against
the door and thread the re-
tainer (R) onto the adaptor (H).
2. Securely tighten using
supplied spanner wrench (S).
K
R
S
Spindle V-groove
STRIKE INSTALLATION
1. Using the template mark PK.1182 the strike mounting holes and centering points.
2. Overlay strike and trace outline.
3. Mark (2) points, 5/16” above and below center point. Using a 1”
spade bit drill 1-1/4” deep at both points. Chisel out remaining material.
4. Predrill screw holes using 1/8” bit. Chisel outline of strike as shown.
5.Install dustbox (A) and strike (B) with strike screws (C).
C B A