Actiontec SBWD100A, SBT100U Installation Guide - Manual

Wireless
Display Kit
Model # SBWD100A & Model # SBT100U
Installation Guide
This Installation Guide will walk you through the easy steps
to set up your ScreenBeam Wireless Display Receiver and
USB Transmitter. During this process, we’ll show you how to:
A Install the Receiver
B Install the Software
and USB Transmitter
C Pair the Receiver and
USB Transmitter
NEXT
ScreenBeam
Step
3
A new screen appears.
Select the Receiver, then
click Connect.
Step
4
A PIN appears on your
HDTV screen.
Step
5
Enter the PIN in the
ScreenBeam software application
within 60 seconds, then click Next.
The ScreenBeam Transmitter and
Receiver are now paired.
You should see the screen of the
laptop/PC on the HDTV.
Go to www.actiontec.com/screenbeamkit for product support,
updates, and more information, including:
• Firmware • Troubleshooting • User Manual • FAQs
For Wi-Fi Miracast or Intel WiDi Devices
• Wi-Fi Miracast: You can connect directly to the ScreenBeam
Receiver from a Windows 8.1 or Android 4.2 device.
Visit www.actiontec.com/wirelessdisplay for compatibility
and setup instructions.
• Intel WiDi: If your system can run Intel WiDi 3.5 (or higher),
you can also connect it directly to the ScreenBeam Receiver.
Visit www.intel.com/go/wirelessdisplayupdate to verify.
IMPORTANT: Federal Communication Commission (FCC) Radiation
Exposure Statement:
This EUT is compliance with SAR for general population/uncontrolled exposure
limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the
measurement methods and procedures specified in OET Bulletin 65 Supplement
C. This equipment should be installed and operated with minimum distance
1.5 cm between the radiator and your body.
Frequently Asked Questions
ScreenBeam displays a screen that seems to be larger than my
TV can handle. How can I fix this?
Right-click the ScreenBeam icon in the Windows system tray, at the
bottom right of the desktop. A menu will appear. From the menu,
select Preferences, then adjust the screen size.
How can I update my Wireless Display Receiver firmware?
Go to http://www.actiontec.com/screenbeamkit to download
the latest firmware and refer to the upgrade instructions
posted online.
Do I need to install ScreenBeam software or the USB
Transmitter included with the ScreenBeam Kit to connect to a
Miracast or Intel WiDi device?
No. For Miracast devices, refer to the user guide of the device’s
manufacturer. For WiDi-capable systems, make sure your system
driver and WiDi software are updated to the latest revision.
I’m seeing a mosaic display on my HDTV. What should I do?
First, make sure the laptop/PC meets the recommended system
requirements. If you’re seeing a constant mosaic picture,
disconnect, then reconnect the ScreenBeam connection. Also,
make sure the Wireless Display Receiver is not hidden inside a
cabinet, as this can reduce performance.
I’ve inserted the software CD into the CD-ROM drive, but it
doesn’t install. What should I do?
In Windows Explorer, browse to the CD-ROM drive (e.g., D:), then
locate and double-click on the “Setup.exe” file.
Should I be concerned if Windows’ firewall or anti-virus
software warns that ScreenBeam is trying to open a port?
ScreenBeam requires Windows to temporarily open a port to
stream content to the TV. Click Allow when the message appears.
How can I update my ScreenBeam Wireless Display software?
Open the ScreenBeam Wireless Display application. Right-click
on the ScreenBeam Receiver you’ve previously connected to and
select “Check for updates…” . Make sure the laptop/PC is
connected to the Internet.
My laptop/PC displays the following message: “Color scheme
has been changed.” Is this a problem?
No. Select “Keep the current color scheme and don’t show this
message again.”
Why am I unable to play a DVD or Blu-ray disc when connected
to ScreenBeam?
Currently, ScreenBeam does not support the streaming of
protected content such as DVD/Blu-ray movies, TV shows, etc.
What should I do if the ScreenBeam Wireless Display software
cannot connect or pair with ScreenBeam Receiver?
Reboot the laptop and power cycle the ScreenBeam Receiver. Also,
try selecting a different wireless channel before connecting. To do
this, from the “Add a Receiver” screen, click on the wireless channel
drop-down menu, then select a different wireless channel.
Part # 0530-0683-002
© 2013 Actiontec Electronics, Inc. ScreenBeam and the Actiontec logo are
registered trademarks or trademarks of Actiontec Electronics, Inc., in the U.S. or
other countries. All other names are properties of their respective owners.
This product has a 1-year Limited Hardware Warranty and 90-day free software
updates from date of purchase.
Local Law
This Limited Warranty Statement gives the customer specific legal rights. The
customer may also have other rights which vary from state to state in the United
States, from province to province in Canada, and from country to country
elsewhere in the world.
To the extent that this Limited Warranty Statement is inconsistent with local law,
this Statement shall be deemed modified to be consistent with such local law.
Under such local law, certain disclaimers and limitations of this Warranty
Statement may not apply to the customer.
Go to http://www.actiontec.com/products/warranty.php for more information.
Declarations of Conformity (DoC)
To obtain the complete DoC form in softcopy, go to the
Actiontec Electronics Declarations of Conformity EU/EEA website
at http://international.actiontec.com/support/doc
For GNU General Public License (GPL) related information, go to
http://opensource.actiontec.com
The symbol at right is placed in accordance with the European
Union Directive 2002/96 on the Waste Electrical and Electronic
Equipment (the WEEE Directive). If disposed of
within the European Union, this product should be
treated and recycled in accordance with the laws of
your jurisdiction implementing the WEEE Directive.