Actiontec SBWD100A Education Edition - Manual (Page 2)

Welcome!
Step
2
Plug one end of the supplied HDMI cable into the HDMI
port on the Receiver, and the other end into an available HDMI
port on the HDTV.
Step
3
Plug the connector of the power cord into the Receiver,
and the AC adapter into a power outlet.
Flip this Guide over to continue
A
Install the Receiver
Thank you for your purchase of the ScreenBeam Pro - Education
Edition Wireless Display Receiver. Once connected to your
compatible mobile device, you’ll be able to project your device’s
screen wirelessly, to a selected HDTV monitor or projector.
1 B
Connect Using Intel WiDi App
Step
2
The device scans for
available receivers. Select the receiv-
er with the same name as seen on
the HDTV and click Connect. (The
Connect Automatically checkbox is
optional.)
Step
1
Get the Receiver, Power Adapter, and HDMI cable from
the product box.
Step
1
Find the Intel Wireless Display application on the device
and launch it. To find the application, go to Windows Search on
your device and search for “Intel WiDi” in your apps.
Note: Make sure the device supports Intel Wireless Display (WiDi)
software version 3.5 or higher. To find out what version of Intel
WiDi your device has, enter the Intel WiDi application and click
Help, then navigate to the “About WiDi” section. To obtain the
latest Intel WiDi software and drivers, go to:
http://www.intel.com/go/wirelessdisplayupdate
Step
4
The HDTV displays
messages to show the status of the
connection process.
Step
4
Make sure the HDTV is turned on and set to display the
input from the correct HDMI port (the one you plugged into
during Step 2).
Display Tip: If the edges of the device screen cannot be seen on
the HDTV, adjust cropping. To do this, enter the WiDi application
and click Settings. Navigate to the “Picture and Sound” section,
click Adjust cropping…, and adjust the HDTV picture by clicking
plus (+) or minus (-).
5
Verify that the Ready to
Connect screen appears on
the HDTV.
Step
5
A Connection Successful
screen appears on your device’s
screen, as well as on the HDTV.
When Steps 1, 2, and 3 are complete, the hardware should be
connected as shown in the figure below.
Note: The power outlet and cable may appear different than
those shown in the figure.
Note: If your device’s OS is Windows 8.1 or higher, proceed to
2 section B (“Connect Using Windows 8.1 or Higher”) for
connection instructions.
The Receiver is now connected to your HDTV. Proceed to one of
the next three sections of this Guide (depending on the device
you are using to connect to ScreenBeam Pro) to finish the
connection procedure.
2 B
Connect Using Windows 8.1 or Higher
Step
1
On a Miracast-enabled Android device, locate and open
the Wireless Display Application.
Note: The name of the Wireless Display Application depends on
the device type and model. Refer to the device’s carrier or
manufacturer user manual for more details.
Step
2
The Wireless Display Application scans for available
receivers. Select the ScreenBeam Receiver from the list.
3
Step
1
Step
2
Step
3
Step
4
Step
5
3 B
Connect Using Miracast-Enabled Device
C
Device Management
You can connect to ScreenBeam Pro from a Miracast-enabled
Android device, such as a smartphone, tablet, or game console (find
the wireless display feature under Settings). Also, the device should
be running the latest software for best performance.
Note: If you are running Windows 8.1 and the screens above do
not appear, go to http://www.actiontec.com/widi81 for the
latest software updates.
Log into the IT Management Console
Step
1
Connect to the Receiver SSID
(which is displayed on the Ready To
Connect screen) from a wireless enabled
laptop.
Enter the PIN provided by your
system administrator (or as displayed on
the TV screen), and then connect.
Note: The default PIN is "12345670".
Enter the PIN provided by your system administrator (or as
displayed on the TV screen), and then connect.
Note: The default PIN is "12345670".
Step
Enter the PIN provided by your
system administrator (or as displayed on
the TV screen) on the WiDi device, and
then click Continue.
Note: The default PIN is "12345670".
You can obtain the PIN from your
system administrator if no PIN is
displayed on the HDTV.
3
Step
The device management webpage provides the ability to
manage the receiver’s settings (such as PIN enforcement, HDMI
power management, and firmware upgrade).
Select the ScreenBeam Receiver
from the list.
From the Project screen, select
Add a wireless display.
From the Charms menu, click the
Project icon.
From the Windows desktop,
navigate to the Charms menu and select
Devices. You can also use the shortcut
keys, Windows + K.
NEXT
Step