Actiontec MWTV200R, MWTV200T Installation Guide - Manual (Page 2)

MyWirelessTV
Multi-Room Wireless
HD Video Kit
NEXT
Model # MWTV200KIT (MWTV200T/MWTV200R)
D Troubleshooting C Setting Up IR Control (Optional)
Quick Start Guide
This Quick Start Guide will walk you through the easy steps
to set up MyWirelessTV. During this process, we’ll show
you how to connect a second HDTV to an existing HDTV
cable/satellite box, DVR, or other HDMI device (Blu-ray
player or gaming console, for example).
A How MyWirelessTV Works
B Connect the Cables
C Setting Up IR Control
D Troubleshooting
You will need the following items from your MyWirelessTV kit:
•
Wireless HD Transmitter
•
Wireless HD Receiver
•
Two (2) Power Supplies
•
Two (2) HDMI Cables
•
IR Blaster Cable
•
IR Extender Cable
© 2011 Actiontec Electronics, Inc. Actiontec, Actiontec Installation Buddy, Creative Solutions for the Digital Life,
and the Actiontec logo are trademarks or registered trademarks of Actiontec Electronics, Inc. in the U.S. or other
countries. All other names are properties of their respective owners.
Product photo may differ from actual product, however functionality remains as stated above.
Specifications are subject to change without notice.
FREQUENTLY ASKED QUESTIONS
1
Q
I’m not seeing anything on the TV screen near the
Transmitter.
A
Check the cable connection from the source (i.e. Cable/
Satellite Set Top Box) to the Transmitter and from
Transmitter out to the HDTV.
2
Q
My cables are connected properly, but I’m still not
seeing video on my TV screen.
A
Make sure the source device is powered on and the correct
source input is selected on your HDTV.
3
Q
I’m not seeing anything on the TV screen next to the
Receiver.
A
Check the cable connection from the MyWirelessTV
Receiver out to the HDTV. Also, make sure the correct
source input is selected on the HDTV.
4
Q
I can’t control my source device (Set Top Box, Blu-Ray
Player, etc.) from my 2nd HDTV.
A
Make sure the IR blaster sensor is pointed directly to the
source device’s IR (infrared) window. Also make sure the
Receiver or the IR Extender cable is in line-of-sight of the
remote control.
Your HDTVs and cable/satellite box should be connected as
shown in the previous diagram. You can now start enjoying
HDTV anywhere you want it!
Step
7
c
Place the flat end of the IR
Blaster cable in front (not directly over)
of the remote sensor of the source
device.
5
Q
I can’t change my channel or volume with the remote
control included with the MyWirelessTV Kit.
A
The MyWirelessTV remote control provided is intended
for switching multiple input, pairing configuration, and
software update. It is not a universal remote control.
6
Q
I do not see any video when I connect to my PC/
Laptop with HDMI to the MyWirelessTV.
A
Make sure the HDMI output display is selected from your
PC/Laptop. Refer to your PC/Laptop’s user manual.
7
Q
The video quality is poor.
A
You may need to adjust the orientation of the Transmitter
and Receiver. Use the Wireless Power Indicator to improve
the wireless signal between the two devices. You may
want to try orienting the Transmitter and Receiver fronts
to be pointing more directly at eachother. To learn more,
see the MyWirelessTV user manual.
Step
7
a
Get the IR Blaster cable
from MyWirelessTV kit. The IR Blaster
cable has a black connector.
Step
7
b
Plug the IR Blaster cable’s
black connector into the Transmit
port on the back of the Transmitter.
Step
6
a
Get the IR Extender cable
(with the green connector) from the
MyWirelessTV kit.
Step
6
b
Plug the IR Extender cable’s
green connector into the Green port
on the back of the Receiver.
Step
6
c
Remove the protective
covering of the doublestick tape and
attach the flat end of the IR Extender
cable to the front corner of the HDTV
bezel or frame.
Part No: 0530-0660-000 QS1155/0811
CAUTION
RISK OF EXPLOSION IF REMOTE CONTROL BATTERY IS
REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS.
The IR Blaster and IR Receiver work together to let you control
the source device (the device to which you connected the
Transmitter: DVR, Blu-ray Player, etc.) from the Receiver location,
whether it's in the next room, or on the other side of the house.
For example, if your source device is in the living room, and you've
set up your My Wireless TV in your bedroom, the IR Blaster/Receiver
allows you to control the source device from your bedroom.
If you are using the MyWirelessTV Kit in the same room,
the IR Blaster is not needed.
Use an IR Extender cable if the receiver is hidden or you want it
to be hidden. Use of this cable is optional.
For Technical Support call
1-888-436-0657
How to Videos, User Manuals, Wall Mount Templates, Software
Updates and other information are available Online at
https://www.actiontec.com/products/product.php?pid=219
MWTVkit_QS12_QS sngl pnl 9/8/11 12:27 PM Page 2