Draw-Tite 65050 FRONT MOUNT RECEIVER - Manual

Installation Instructions
Chevrolet Silverado 2500 HD, 3500 HD
GMC Sierra 2500 HD, 3500 HD
Note: Fascia trim required.
Obtain vehicle owners approval before cutting
Part Numbers:
65050
Hitch Shown In Proper Position
Equipment Required: Tape, Utility Knife,
Tape Measure & Marking Pencil.
Wrenches: 21mm, 3/4” & (2) 18mm
Drill Bits: None
Trim fascia for receiver tube.
1.
Trim fascia. See fascia trimming information for proper vehicle model:
Note: CONSULT VEHICLE OWNER BEFORE TRIMMING.
2. Remove the flange nuts on the 2 bolts (1 each side) from existing tow hooks. On passenger’s side loosen bolt until flush with
the inboard frame rail. On driver’s side remove bolt. Keep for re-installation.
3. Raise hitch into position and push both bolts through brackets to support the hitch.
Note: Due to vehicle variation (if needed) tape flat washer (Item 5) to inside frame rail over the forward holes.
Note: If there is interference with the bumper support loosen DO NOT remove and lift the bumper upward for extra clearance.
4. Tape spacers (Item 3) to handle nuts (Item 4).
5. Bend and insert handle nuts thru access holes in frame and install two (2) 1/2”-13 bolts and conical washers as shown.
6. Tighten all fasteners to the required torque specification. Caution: Hold handle nuts in place to prevent them from rotating.
7. If bumper support was loosened in Step 3 re-tighten.
Rev. A 8-17-07 65050N Sheet 1 of 6 z 2007 Cequent Towing Products
Flat washer (if needed) Qty. (1) 5 Conical washer Qty. (2) 2
Spacer Qty. (2) 3
Handle nut 1/2-13” Qty. (2) 4 Hex bolt 1/2-13” X 1.500 GR5 Qty. (2) 1
Tighten all 1/2 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all M12 CL10.9 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
Fastener Kit: 65050F
CARGO CAPACITY – Do not exceed
500 LB. (227 Kg) or Truck Front
Gross Axle Weight Rating, (GAWR).
MAXIMUM WINCH LINE PULL 9,000 lb.
Fascia trim required. Obtain vehicle owners approval before cutting
NOTE: If front mounted license
plate is present, repositioning
may be necessary.
Caution: Hold handle
nuts in place to prevent
them from rotating.
Inboard rail
34
1
2
Note: Fasteners typical
both sides
Bumper support
NOTE: Pin and clip
installed from behind
Fascia.
Forward hole – if needed tape flat
washers (Item 5). See Step 3
Chevrolet
GMC
Fascia
Flange nuts for existing
tow hooks
3 4
Tape
Tape spacer (Item 3) to
handle nut (Item 4)
Access hole
Tow hooks and
fascia not shown.
MAXIMUM WINCH LINE PULL (4086 Kg)
Existing M12 Bolt - Typ
Form: F205 Rev A 5-6-05