Draw-Tite 75761 MAX-FRAME RECEIVER User Manual
Installation instructions, Bmw x1, Part numbers
Installation Instructions
BMW X1
Only fits vehicles with Panoramic Moonroof
Part Numbers:
75761
87630
44684
75366
U-HAUL
Hitch Shown In Proper Position
Equipment Required:
Rivet gun, screwdriver or trim tool,
small punch.
Wrenches:
8mm, 10mm, 18mm, & (2) 3/4”
Drill Bits:
NONE
Lower fascia trim
Center
mounting
strap
1.
Remove lower fascia trim on the rear of the vehicle by removing the (5) fasteners and (2) plastic rivets that secure the bottom fascia to the
vehicle. Punch out the center of the rivets head by using a small punch or blunt nail. Carefully slide screwdriver or trim panel tool between the
panels covering to loosen rivets, and remove remaining rivet head. Working your way from outside (rivet location), slowly pull up fascia trim.
2.
Remove or loosen the (2) rear appearance panels on the bottom of the vehicle for additional clearance during hitch installation if necessary.
3.
Remove the inside muffler hanger using a 10mm socket.
4.
Remove the (4) flange nuts from the bumper. See Figure 2.
5.
Place (item 1) (4) flat washer onto each studs as shown. See Figure 3. Both sides.
6.
Lift the hitch into position onto the studs on the driver’s side first, going over the exhaust taking extreme caution around ECV valve if present.
7.
Swing the hitch into place and re-install the existing M12 flange nuts.
8.
Remove the bolt from the suspension support frame. Slide the center mounting strap between the support and existing plate. Re-install existing
M12 bolt as shown.
9.
Attach the center support bar to the hitch as shown in figure 4.
10. Reattach exhaust hanger bolt.
11. Reinstall the (2) underbody appearance panels.
12. Tighten all fasteners to the required torque specification.
13. Reinstall the rear fascia appearance panel. Using the plastic rivets provided
Tighten all ½-13 fasteners with torque wrench to75Lb.-Ft. (102 N*M)
© 2012, 2013 Cequent Performance Products, Inc – Printed in Mexico
Sheet 1 of 3
75761N
11-13-13
Rev. D
Tighten all M12 fasteners with torque wrench to 68 Lb.-Ft. (92 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
Fastener Kit:
75761F
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Hitch type
Max Gross
Trailer WT (LB)
Max Tongue
WT (LB)
Weight Distributing
4000 (1816 Kg)
400 (182 Kg)
Weight Carrying
Ball Mount
3500 (1589 Kg)
400 (182 Kg)
Wiring Access Location:
SUV1 & 2
Form: F205 Rev C 9-17-2012
Accessory Rating
C
1
1
1
1
Qty. (16)
Washer ½”
4
4
4
4
Qty. (2)
Hex nut ½-13
2
2
2
2
Qty. (2)
Bolts ½-13 X 2.25 GR5
5
5
5
5
Qty. (2)
Flat washer ½”
3
3
3
3
Qty. (2)
Conical washer ½”
6
6
6
6
Qty. (2)
Plastic rivets
1
1
1
1
2
2
2
2
3
3
3
3
5
5
5
5
4
4
4
4
1
1
1
1
Suspension support
frame
Rear appearance
panel
Suspension
support frame
Figure 1.
Figure 2.
Figure 4.
Remove (4) flange nuts.
1
1
1
1
Figure 3.
Suspension
support frame
Fascia
Existing
flange nuts
Existing
flange bolt
Muffler hanger
area
Existing
support
frame
plate
Note: if vehicle is equipped disconnect the back up sensors during installation.
Note: Loosen existing nut
for ease of installation.
Note: Fasteners typical
both sides