Draw-Tite 24750 SPORTFRAME HITCH - Manual

Installation Instructions
Nissan Sentra
Part Numbers:
77126
24750
60826
Hitch Shown In Proper Position
Equipment Required: Pull Wire (provided)
Wrenches: 3/4, 7/8, 11/16
Drill Bits: None
1. Open trunk, lift rug and remove spare tire.
2. Remove both rubber sealing plugs from the bottom of spare tire well. Install carriage bolts and blocks as shown, longer bolt in rearmost hole.
3. Remove (2) plastic fascia push rivets from bottom of rear bumper fascia and retain for re-installation.
4. Position hitch uprights above fascia and loosely attach blocks, conical washers and nuts at spare tire well attachments as shown. Be sure to
install spacer blocks between hitch side arm and rearward attachment to spare tire well as shown.
5. Install blocks and carriage bolts into slots in bumper and down thru slots in hitch uprights using pull wire provided as shown. Install conical
washers and nuts
Note: Kink pull wire to keep block independent of bolt as shown in Figure 2.
6. Reinstall push rivets back into bumper fascia.
7. Apply sealant at carriage bolt attachments inside spare tire well to prevent the intrusion of water and exhaust fumes to vehicle interior.
8. Replace spare tire and rug.
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Rev. D 10/27/06 24750N Sheet 1 of 3 z 2005, 2006 Cequent Towing Products
Conical Toothed Washer 7/16 Qty. (2) 9 Block ¼ x 1-3/4 x 2-1/2 Qty. (2) 4
Block ¼ x 1 x 3 Qty. (2) 5
Hex Nut 7/16-14 Qty. (2) 8 Block ¼ x 2 x 2 Qty. (2) 3
Hex Nut ½-13 Qty. (2) 7 Carriage Bolt ½-13 x 2-1/4 Qty. (2) 2
Conical Toothed Washer ½” Qty. (2) 6 Carriage Bolt 7/16-14 X 1-1/2 Qty. (2) 1
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Drawbar must be used in the
Rise position only.
Drawbar Kit:
3593
Fastener Kit: 24750F
Form F206 Rev A 5605
Bumper
Spare Tire
Well
Fascia
23
Bumper
Bumper Fascia
Spare Tire
Well
Hitch Side Arm
Apply sealant
Between blocks
And well
Hitch Uprights
Pull Wire
Remove rubber
Sealing plugs
23
67
1598
67
4
98
15 Existing hole
Kink pull wire to keep block
independent of bolt
Example of pull wire procedure
Bumper
Figure 2
Figure 1
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4