Draw-Tite 24848 SPORTFRAME HITCH - Manual

Installation Instructions
VW Passat (
Except 4Motion)
VW Passat Wagon (
Except 4Motion)
VW CC
Note: Fascia trim required
Part Numbers:
24848
60264
77221
24831
(U-HAUL)
Hitch Shown In Proper Position
Wiring Access Location: Passat Sedan PC1, 2
Wagon PC1,2
CC- TBA
Equipment Required: Utility Knife
Wrenches: T-20, T-25 Torx Driver y, 13mm,
11/16” and Extension Driver
Drill Bits: 1/2”
1. Remove plastic fascia covering the passenger side frame rail of the vehicle by removing the (5) Torx screws. Return plastic fascia
covering and screws to vehicle owner. Remove the two plastic fascia nuts from the fascia tabs (Do not discard).
2. Remove the (2) bolts from the exhaust hanger bracket as shown in Figure 1 to lower the exhaust. Return bolts to owner.
3. Slide the driver’s side bracket above the exhaust bracket. Note: Sandwiching the hitch bracket between frame and exhaust hanger bracket.
Using the (2) M8 bolts loosely tighten the fasteners. Note: Rotate the hitch for ease of installation.
4. Align the passenger bracket with the locating edge and the tab see Figure 2 (check hitch for alignment perpendicular of the vehicle
making sure the bracket is flat against the frame rail). The passenger side bracket may need to be pushed flat against the frame
rail. Then using the hitch as a template mark the hole locations. Drill the 1/2” holes.
Optional: Lower the hitch to drill (2) 1/2” hole into the frame rails. Repeat step 3.
5. Fishwire the passenger side fasteners through the access slot in the frame rail, through the side bracket of the hitch (rearward
attachment first) and install conical washers and hex nuts.
6. Trim the Fascia on the driver’s side near the exhaust as needed. Obtain vehicle owners approval before cutting.
7. Reattach fascia tabs
Tighten all 7/16-14 Gr. 5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
z 2009, 2011, 2012 Cequent Performance Products Sheet 1 of 3 24848N 1-9-12 Rev. D
j
Qty. (2) Bolt M8 X 1.25 X 55 CL 9.8
m
Qty. (2) Conical Washer 7/16”
k
Qty. (2) Bolt, Carriage 7/16-14 X 1.50 GR 5
n
Qty. (2) Nut 7/16-14
l
Qty. (2) Block ¼ X 1 X 3
o
Qty. (1) Pull wire
Tighten all M8 X 1.25 CL9.8 fasteners with torque wrench to 20 Lb.-Ft. (27 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Drawbar must be used in the
RISE position only.
Drawbar Kit:
3594
Fastener Kit: 24848F
Form F206 Rev A 5605
Fascia
Frame Rail
Exhaust Hanger
Figure 2
Figure 1
Passenger Frame Rail
Cut-away for View
Fascia area to be trimmed,
depending on vehicle style
Frame Rail
j
j
m
n
k
l
Pull Wire
Exhaust Hanger
Bracket
Existing
Weld Nuts
Drilled Holes
Exhaust
Tab
Access Slot
Locating
Edge
Fascia trim required. Obtain vehicle owners approval before cutting
Tab
Locating
Edge
o