Draw-Tite 22292 PROPORTIONAL WIRING ADAPTER - Manual

ENGLISH
1. Make sure the vehicle is off with the keys
removed from the ignition.
2. Locate the instrument cluster finish panel
in the center of dash on driver side.
d Pry
the panel out and away from the dash
being careful not to damage the trim or
panel. Unplug the housings attaching the
panel being careful not to damage locking
tabs and set aside.
3. Option 1:
Locate and remove two bolts, exposed in
step 2. Remove bin. Unplug grey connector
from back of bin.
e
Option 2:
On vehicles equipped with factory brake
controller locate the large grey housing
matching the mating half of the adapters
connector. Housing will be plugged into the
back of the unit. Additional harnesses may
need to be unplugged to gain access to its
location.
NOTE:
When disconnecting the factory installed
brake control, you will get a fault code
displayed on the message center of the
dash.
4. Plug the brake control adapter into the
vehicle’s electric brake control harness
connector.
5. Locate a routing path for the adapter to
exit the bottom of dash.
TIP:
Use a flash light to shine light up though
the bottom of dash to locate a hole to exit
the dash.
6. Complete the installation per the electric
brake control manufacturer’s instructions
and mount the unit as directed. Perform
test procedures as instructed.
7. After brake controller is installed, plug in all
connectors that were not used back into
the original housings and snap access
panel back into place.
NOTE:
Vehicles not equipped with OEM trailer tow
package, may require fuses and relays to
complete output and battery feed circuits
(sold separately). Consult owners manual
for locations.
WARNING
Overloading circuit can cause fires. DO
NOT exceed lower of towing manufacturer
rating or:
• Max. 3 AXLES: 6 BRAKES 18 amps
Read vehicle's owners manual &
instruction sheet for additional information.
22292-037 Rev. A 1/27/09
Installation Instructions
Directives de Montage
Instrucciones de Instalación
Electric Trailer Brake Control
Wiring Adapter
Adaptateur pour câblage
de commande de frein de
remorque électrique
Adaptador del cableado de
control eléctrico del remolque
TRAILER BRAKE CONTROLLER (OUTPUT)
CONTRÔLE DE FREIN DE
REMORQUE (SORTIE)
CONDUCTOR DEL CONTROLADOR DE
FRENO (SALIDA) AL FRENO ELÉCTRICO
DEL REMOLQUE
FUSED TRAILER BRAKE CONTROLLLER
BATTERY FEED
ALIMENTATION À FUSIBLE DE LA
BATTERIE AU CONTRÔLE DE FREINS
CONDUCTOR (CON FUSIBLE) DE LA
BATERIA AL CONTROLADOR DEL FRENO
DEL REMOLQUE
VEHICLE STOP LAMP SWITCH TO
BRAKE CONTROLLER (INPUT)
COMMUTATEUR DE FEUX D'ARRÊT DU
VÉHICULE AU CONTROLE DE FREINS
INTERRUPTOR DE LUCES DE FRENADO
DEL VEHICULO AL CONTROLADO DE
FRENO (ENTRADA)
GROUND
MISE À LA TERRE
TIERRA
Wiring Adapter Housing (containing Male Terminals) - Wire Side
Logement de l'adaptateur de câblage (contenant les bornes mâles) - Côté fil
Protector del adaptador de cables (contiene los terminales machos) - Alambre el lado
•
d
•
e
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEZ CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.