Draw-Tite 20270 WIRING ADAPTER - Manual

ENGLISH
1. Make sure the vehicle is off with the keys
removed from the ignition.
2. Locate access panel in the center of dash
on passenger side. Using a trim panel
puller, locate notch in panel and pry the
panel out and away from the dash being
careful not to damage the trim or panel
d .
Unplug the housings attaching the panel
being careful not to damage locking tabs
and set aside
e .
3. On vehicles equipped with factory brake
controller locate the large grey housing
matching the mating half of the adapters
connector. Housing will be plugged into the
back of the unit
f . Additional harnesses
may need to be unplugged to gain access
to its location.
NOTE
When disconnecting the factory
installed brake control, you will get a
fault code displayed on the message
center of the dash.
4. On vehicles without a factory brake
control locate grey housing on the back
of the trim panel located directly left of
the access panel.
5. Carefully pull the housing towards the
access panel and plug in the mating grey
housing from the brake control adapter
g .
6. Locate a routing path for the adapter to
exit the bottom of dash h .
TIP
Use a flash light to shine light up though
the bottom of dash to locate a hole to exit
the dash.
7. Use butt connectors and attach the wires
from the adapter to the corresponding
wires on the electric brake control,
following the brake control manufacturer's
installation instructions. Perform test
procedures as instructed.
8. After brake controller is installed, plug in
all connectors that were not used back
into the original housings and snap access
panel back into place.
NOTE
Vehicles not equipped with OEM trailer tow
package, may require fuses and relays to
complete output and battery feed circuits
(sold separately). Consult owners manual
for locations.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer
rating or:
• Max. 3 AXLES:
6 BRAKES (18 amps)
Read vehicle's owners manual &
instruction sheet for additional information.
20270-037 Rev. A 06/18/07
Installation Instructions
Directives de Montage
Instrucciones de Instalación
Electric Trailer Brake Control
Wiring Adapter
Adaptateur pour câblage
de commande de frein de
remorque électrique
Adaptador del cableado de
control eléctrico del remolque
TRAILER BRAKE CONTROLLER (OUTPUT)
CONTRÔLE DE FREIN DE
REMORQUE (SORTIE)
CONDUCTOR DEL CONTROLADOR DE
FRENO (SALIDA) AL FRENO ELÉCTRICO
DEL REMOLQUE
FUSED TRAILER BRAKE CONTROLLLER
BATTERY FEED
ALIMENTATION À FUSIBLE DE LA
BATTERIE AU CONTRÔLE DE FREINS
CONDUCTOR (CON FUSIBLE) DE LA
BATERIA AL CONTROLADOR DEL FRENO
DEL REMOLQUE
VEHICLE STOP LAMP SWITCH TO
BRAKE CONTROLLER (INPUT)
COMMUTATEUR DE FEUX D'ARRÊT DU
VÉHICULE AU CONTROLE DE FREINS
INTERRUPTOR DE LUCES DE FRENADO
DEL VEHICULO AL CONTROLADO DE
FRENO (ENTRADA)
GROUND
MISE À LA TERRE
TIERRA
Wiring Adapter Housing (containing Male Terminals) - Wire Side
Logement de l'adaptateur de câblage (contenant les bornes mâles) - Côté fil
Protector del adaptador de cables (contiene los terminales machos) - Alambre el lado
•
d
•
h
•
e
•
g
•
f
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEZ CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.