Draw-Tite 118521 T-ONE CONNECTOR - Manual

READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEz CECI En PREmIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRImERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.
118521-037 Rev. A 11/03/10
Installation Instructions
Directives de montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
e h
g
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, Flat Screwdriver, Test-Probe,
Pliers, Protective Cloth, 10mm Socket or Wrench
1. Open rear door and fold rear seat forward.
Temporarily remove the rear threshold plate. d e
nOTE
Use pliers and protective cloth to remove
threaded cargo net hook(s). Set aside all items
removed being careful not to damage parts.
2. Locate fuse panel cover near the rear seat on
the driver’s side. Open the cover to access the
relays and fuses. Being careful not to damage
clips, partially remove the lower interior trim
panels on vehicle. f g
nOTE
Note use pliers and protective cloth to remove
threaded cargo net hook(s).
3. Starting from the cargo area, route the white
T-Connector end up and behind the trim panel
to the rear fuse box.
4. If the vehicle is equipped with accessory backup
sensors, unplug the sensor harness 14 pin
connector from the rear fuse box connector. If not,
go to step 5. Plug the backup sensor harness into
the the other mating T-connector end. h
5. Plug the white 14 pin T-connector end into the
mating connection in the fuse box connector. h
6. Route the white wire with eyelet towards the
back of the vehicle near the threshold area.
Locate existing ground stud. Loosen bolt, place
screw eyelet on stud and re-tighten bolt. i
WARnInG
Make sure all other ground connections are secure
when removing and reattaching the ground stud.
7. Locate the T-Connector’s Grey 12-Pin connector
and insert it into the mating connector located
on the black box-module. Check to see that the
mating surfaces of the wiring connectors match.
All connector surfaces should be clean and free
of dirt. Be careful not to damage the locking tabs
and be sure that connectors are fully inserted
with locking tabs in place.
8. Locate a flat surface in an out of the way place
and mount the T-Connector’s black box-module,
to prevent damage or rattling.
nOTE
This surface should be in an area that is free of
any mositure and mounted in an area that it is
high enough where it could not be exposed to
direct contact with any water or liquid substance.
WARnInG
The black box-module is intended to be mounted
ONLY in the INTERIOR of the vehicle. Mounting
on the exterior or areas exposed to the elements
or moisture could cause serious damage to the
vehicle and module. Secure the remainder of the
T-Connector harness with the cable ties provided,
to prevent damage or rattling and being careful
to avoid any areas that would pinch, cut or melt
the wire.
9. Install a 10 amp fuse into the rear fuse box
position #8. Install two 7.5 amps fuses into
the rear fuse box positions #2 & #11.
WARnInG
Overloading circuit can cause fires. DO NOT
exceed manufacturer rating. Read vehicle’s
owner’s manual & instruction sheet for
additional information.
10. WARnInG
All connections must be complete for the
T-Connector to function properly. Test and
verify installation with a test light or trailer
once installed. For initial test, reset vehicle
electrical system by temporarily removing the
key from the ignition.” Re-insert key and turn
key to the proper position.
11. Mount the 4-flat end in an accessible location.
If routing the wire thru a grommet and along the
exterior of the vehicle, be careful to avoid any
hot pipes, heat shields, the fuel tank or any other
points that may pinch or break the wire.
12. Reinstall the threshold, trim panel, cargo net and
cover. Being careful not to pinch or cut the wires.
WARnInG
Overloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer rating or:
• Max. stop/turn light: 2 per side (4.2 amps)
• Max. tail lights: (7.5 amps)
Read vehicle’s owners manual & instruction sheet
for additional information.
d
f i
Honda Odyssey