Draw-Tite 118597 T-ONE CONNECTOR - Manual

10. Secure the remainder of the T-Connector harness with
the cable ties provided, to prevent damage or rattling
and being careful to avoid any areas that would pinch,
cut or melt the wire.
11. Reinstall the threshold, storage covers, floor covering
and other items removed during installation, being
careful not to pinch or cut the wires.
NOTE
Store 4-Flat connector in rear cargo area when not
in use.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of vehicle manufacturer rating or:
• Max. stop/turn light: 2 per side (4.2 amps)
• Max. tail lights: (7.5 amps)
Read vehicle’s owners manual & instruction sheet
for additional information.
ENGLISH
TOOLS NEEDED:
Trim Panel Remover, 10mm Socket &
Ratchet or 10mm Wrench, Drill (3/32” Drill Bit),
1/4” socket, Wire Crimpers, Wire Cutters,
Philips Head Screwdriver, Test-probe
1. Open rear door and remove the access panel
doors on both sides to access vehicle’s wiring
connectors d. Several trim panel fasteners will
need to be removed to remove the panels e.
2. There will be connection points matching the ends
of the T-Connector adapter on the back of each of
the vehicle taillight housings f. Disconnect the
wire harness.
3. Beginning on the driver’s side, plug the T-Connector
harness containing the yellow wire in between the
vehicle’s mating connectors.
NOTE
Be careful not to damage the locking tabs and be
sure that connectors are fully inserted with locking
tabs in place.
4. On the Driver’s side route the T-Connector end with
the green wire up through the trim panel access hole,
across the top threshold, & through the passenger
trim panel access hole g.
NOTE
For ease of installation attach harness (two connectors)
to fish wire and carefully pull toward passenger side.
5. Locate a suitable grounding point on the driver’s
side near the connectors. Drill a 3/32” hole and
secure white wire with eyelet using screw provided.
Do not drill into any exposed surfaces.
CAUTION
Verify what is behind any surface prior to drilling to
avoid damage to the vehicle and/or personal injury.
Do not drill into any exposed surfaces.
6. WARNING
Make sure module is mounted so that the epoxy
side of the module is pointed towards the ground
to prevent any water buildup.
7. On the driver’s side, locate the black 12 ga. Power
wire from the T-Connector box. Attach the black
12 ga. wire provided. Either route the black wire thru
a grommet and along the exterior frame or follow the
existing wiring along the thresholds into the engine
compartment up to the battery avoiding areas that
may pinch or break the wire h.
8. Disconnect the vehicle’s Negative (-) battery cable.
If not removed, remove the fuse from the yellow fuse
holder (provided). After cutting the fuse holder wire
i, attach the ring terminal and secure to the vehicle’s
Positive (+) battery cable. Connect the other end of
the fuse holder to the black 12 ga. wire, using the
yellow butt connector (provided) j.
WARNING
Read and follow all warnings and cautions printed
on the tow vehicle’s battery.
9. Reconnect the vehicle’s Negative (-) battery cable
and install the 10 amp fuse into the fuse holder
from step X.
WARNING
All connections must be complete for the T-Connector
to function properly. Test and verify installation with a
test light or trailer once installed. For initial test, reset
vehicle electrical system by temporarily removing the
key from the ignition.
Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
Nissan NV200
e f
g
d h
i
j
118597-037 Rev. A 5/16/2013
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEz CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.