intimus 319 - Manual (Page 5)

AREA OF APPLICATION:
The intimus 315/319SC2/CC3/CC4 data
shredder is a machine used for shredding general
documents and data carriers such CD’s, DVD’s,
credit cards and 3.5” diskettes.
The machine must only be used to
shred paper, credit cards and CD’s,
DVD’s and 3.5” diskettes.
Shredding other sorts of data carriers
may cause damage to the machine (e.g.
damage to the cutters etc.).
INSTALLATION:
- Unpack the machine and put it together.
- Push waste bin into the frame.
- Connect the machine to the power with the plug
(1) (fi g. 2) (For information on the right fuse for
the plug see “TECHNICAL DATA”).
The socket outlet shall be installed
near the equipment and shall be easily
accessible!
Only operate the machine in enclosed
rooms at temperatures between 5°C
and 35°C!
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by “one person only”.
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of
this machine (dimensions, feed openings,
emergency shutdown devices etc.) does not
provide for any guarantee regarding hazard-
free operation by children.
<< Danger of injury! Keep all
loose articles of clothing, ties,
jewelery, long hair or other loose
objects away from opening!
<< Danger of injury! Never insert fi ngers into
opening!
<< In case of danger switch the machine off
with the mains switch, or with the emer-
gency switch, or unplug the machine!
<< Always unplug the machine from the
mains power supply before opening the
machine!
Repairs may only be performed by trained
personnel!
IMPORTANT SAFETY NOTES
315SC2 315CC3 315CC4 319SC2 319CC3 319CC4
3
9
10
11
4
6
7
8
2
12
13
5
1
5
OPERATION
INITIATION
fi g. 1 fi g. 2 fi g. 3
6 = Control display (fi g. 1)
“Material jam in machine” /
“Simultaneous material feed” / “Light
barrier occupied when moving waste
bin out or switching on”
For the procedures see the relevant
description under the “MALFUNCTION”
section.
a) “Material jam in machine”
Comes on when too much material has
been fed into the cutters. The cutters
jam, then run in reverse for a short time
and stop. The motor switches off.
b) “Simultaneous material feed”
Comes on when material has been fed
into both slots at the same time. The
cutters stop, then run in reverse for a
short time and stop. The motor switches
off.
c) “Light barrier occupied
when waste bin moves out”
Is lit if there is still material in one of
the two feed slots when the waste bin
moves out. The cutters stop. The motor
switches off.
d) “Light barrier covered
when machine turned on”
Comes on when there is still material
in one of the two feed slots when the
machine is switched on.
CONTROLS:
1 = Mains plug (fi g. 2)
When the machine is fi rst plugged in it is
not on.
2 = Function buttons (fi g. 1)
“Ready”/ “Off” / “Stop“
This button has three functions:
a) “Ready”
The machine changes to “Ready” if you
press this button briefl y.
At the same time the integral LED
display comes on.
b) “Off”
The machine switches off if it is in the
“Ready” mode and the button is held
down for about 3 seconds.
Note: The machine switches off
automatically if it is not used for about 5
minutes.
c) “Stop”
If you press this button briefl y when the
cutters are running they switch off and
stop.
3 = Forwards button (fi g. 1)
This button has two functions:
a) If this button is pressed briefl y, the
cutting mechanism runs forwards for a
few seconds, e.g. to remove remaining
material from the cutting mechanism.
At the same time the integrated LED
display lights up.
b) If this button is pressed and held
for approx. two secs., the cutting
mechanism runs forwards continually
and materials to be shredded can be fed
into the machine. At the same time the
integrated LED display lights up.
4 = Reverse button (fi g. 1)
If you press this button the cutters run
backwards for a short time. At the same
time the integral LED display comes on.
5 = Light barrier (Forward motion) (fi g. 3)
The shredding procedure starts as soon
as material is fed into one of the two feed
slots. At the same time the integral forward
button LED display comes on.
GB
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung