Chapin 22149 - Manual

WARNING!
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,
replace hose before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank
for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and
could result in explosive bursting under pressure. If any of these signs are found, discard tank immediately and
replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.
5) Do: Pump plunger 8-10 strokes and inspect for leaks.
6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with
Filling, Pressurizing and Spraying Instructions.
3. Pre-Use Check
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: over fill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten
securely.
8. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing
and Spraying Instructions, except pump unit only 8-10 strokes.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through
opening in cover.
011534-1 (A) R0000
301515
Pump
Assembly
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com
WARNING: Handling the brass parts of this product will expose you to lead, a chemical known
to the State of California to cause birth defects and other reproductive harm. Wash hands after
handling.
Hazard: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions.
Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up. Do not store
or le ave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full
foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent eject-
ing pump assembly and/or solution from striking and injuring you. Never pressurize sprayer by any
means other than the original pump. Do not attempt to modify or repair this product except with
original manufacturer’s parts. Never spray flammable materials or heat, pressure, or gas produc-
ing chemicals. Always read and follow manufacturer’s instructions before use with this sprayer
as some chemicals may be hazardous when used with this sprayer.
Sk-1113-1
1. Hose to Tank
Discharge/ Assembly
• Make sure white outlet tube is attached to outlet tube adapter (Fig. 1A).
• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1B).
• Proper placement of white outlet tube (Fig. 1C).
• Firmly insert the outlet tube adapter into the tank adapter (Fig. 1D) Lining up tab
with notches on the tank adapter.
• Firmly tighten the retaining nut to the tank adapter (Fig. 1E).
Discharge
Assembly
1B
Outlet
Tube
1E
Retaining Nut -
Securely tightened.
1C 1D
No
Gap
Tank
Adapter
Outlet Tube
Adapter
Tab/
Notch
1A
Outlet Tube
Adapter
Outlet
Tube
5. Pressurizing and Spraying
Do: Turn handle clockwise
to tighten. Push handle
down, turn 1/4 turn coun-
terclockwise to release.
Do: Pump until you
feel resistance.
Do: Push handle, down, turn
1/4 turn clockwise to lock.
Begin spraying. Re-pump
sprayer as required to maintain
spray force.
5A 5C 5B
7. To Release Pressure
1) Your sprayer is equipped with a pressure relief/release valve.
To release pressure lift and hold the cap until air is completely
exhausted, OR, turn the valve slowly counterclockwise until you
hear air escaping and wait air is completely exhausted.
2) Do: Stay away from the sprayer until all air has escaped.
6A
Parts, Piezas, Pièces
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-5387
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
6-5943
Nozzle 1.0 GPM
Tobera
Buse
6-5797
Nozzle .5GPM
Tobera
Buse
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions?
Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡
Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas?
No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ?
Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
6-6090
Hose Black
Manguera para trabajos pesados Negro
Tuyau pour service intense Noir
For safety lock-off feature (no-spraying), push trigger
forward and rotate locking mechanism into lock-off
position as shown in fig. 6A.
6. Lock Off
6-8136
Valve Kit
Kit de la válvula
Ensemble de soupape
6-8135
Dripless Shut-off
Cierre antigoteo
Arrêt anti-goutte
2. Nozzle
Attach nozzle to shut-off handle or extension wand.
2A 2B Valve Seat
Nozzle Adapter
Nozzle
To attach nozzle to shut-off, unthread nozzle adapter and re-
move valve seat from extension (2B). Unthread brass extension
nut and metal rod (2D). Assemble valve seat to shut-off then
assemble nozzle adapter as shown in figure (2A).
Note orientation of valve seat. It will leak if assembled wrong .
2C
Metal Rod Brass Extension
OR
Brass Extension Nut
Metal Rod
2D
Metal Rod
6A
Lock
Trigger